Question 151
Which of the following statements about a designated port working in RIPv2 multicast mode are true? (Choose three)
A. The port receives only RIPv2 multicast packets.
B. The port does not receive RIPv1 broadcast packets.
C. The port does not receive RIPv2 broadcast packets.
D. The port receives only RIPv1 multicast packets.
Question 152
Which of the following statements regarding the router ID in OSPF are incorrect? (Choose three)
A. The router IDs of OSPF routers in the same area must be the same, but can be different in different areas.
B. The router ID must be the IP address of an OSPF router interface.
C. The router ID must be configured manually.
D. A router running OSPF must have a router ID for it to operate properly.
Question 153
Which of the following statements regarding Designated Routers in OSPF are correct? (Choose three)
A. DR is elected by all the routers in the same network segment.
B. If the priorities of two routers are different, the router with the lower priority will be elected as DR.
C. If the priorities of two routers are equal, the router with the higher Router ID will be elected as DR.
D. DR and BDR must be adjacent.
Question 154
On the VRP platform, which of the following commands is used to configure the Router ID of a router as 1.1.1.1?
A. router id 1.1.1.1
B. [Huawei]router id 1.1.1.1
C. [Huawei]router-id 1.1.1.1
D. [Huawei]router id 1.1.1.1 255.255.255.255
Question 155
Which of the following OSPF versions is specific to IPv6?
A. OSPFv1
B. OSPFv2
C. OSPFv3
D. OSPFv4
Question 156
The administrator wishes to configure OSPF on a router in the network however the router has no loopback interface.Which value will be used as the router ID?
A. The lowest IP address of the router's active interfaces.
B. The highest IP address of the router's active interfaces.
C. The IP address of the management interface.
D. The priority value of the router.
Question 157
An administrator of a company supporting a large enterprise network wishes to implement OSPF on the network as opposed to RIP. Which of the following points should the administrator use to support his reasoning for this change? (Choose three)
A. OSPF has no hop count limitation.
B. OSPF has a lower routing update overhead.
C. OSPF has a simpler configuration.
D. OSPF supports faster convergence.
Question 158
Which of the following statements regarding single area OSPF are correct? (Choose three)
A. An IP address needs to be configured on a loopback interface of each router before configuring an OSPF area.
B. The value of an area can be from 0.0.0.0 to 255.255.255.255.
C. A single area can be configured using any supported area number.
D. All of the links of the network need to be advertised in Area 0.
Question 159
10.0.1.0/24 O_ASE 150 2 D 10.0.23.3 Serial2/0/0Refer to the display output. Which of the following statements regarding route shown are true? (Choose two)
A. The address 10.0.23.3 has been configured on the peer's serial 2/0/0 interface.
B. The route preference has been changed by the administrator.
C. The metric for the route 10.0.1.0 indicates that two hops are needed.
D. The route has been learned via the OSPF protocol.
Question 160
Which of the following statements regarding link-state database and routing-table of a "single" OSPF area are correct? (Choose two)
A. The link-state databases that all routers build are identical.
B. The link-state databases that all routers build are different.
C. The routing-tables that all routers calculate are different.
D. The routing-tables that all routers calculate are identical.