Question 71
Refer to the exhibit. A network engineer is implementing a configuration checkpoint on a Cisco Nexus 9000 Series Switch. The configuration must skip any existing vPC configuration errors and must complete if there are any configuration errors. The engineer finished the vPC domain configuration part. Which command completes the checkpoint implementation?
A. best-effort
B. stop-at-first-failure
C. atomic
D. verbose
Question 72
An engineer must implement a VXLAN-based data center interconnect. The long-distance transport provided by a service provider is IP-based, supports a maximum MTU of 1554 bytes, and does not support outbound traffic replication. Which action must be taken to build the data center interconnect?
A. Announce host reachability over BGP.
B. Create an IP access list and associate it with VNI to replicate traffic to remote VTEPs.
C. Configure a route map to associate the IPs of the remote VTEPs.
D. Implement BGP EVPN ingress replication.
Question 73
An engineer must perform an initial configuration of VXLAN Tunnel End-Point functionality on the Cisco Nexus 9000 Series platform. All the necessary features are already enabled on the switch. Which configuration set must be used to accomplish this goal?
A. NX9K(config)# interface loopback0 NX9K(config-if)# ip address 10.10.10.11/32 NX9K(config)# interface VLAN10 NX9K(config-if)# ip unnumbered loopback0 NX9K(config)# interface nve1 NX9K(contig-if-nve)# source-interface loopback0
B. NX9K(config)# interface loopback0 NX9K(config-if)# ip address 10.10.10.11/32 NX9K(config)# interface overlay0 NX9K(config-if-overlay)# source-interface loopback0 NX9K(config)# interface VLAN10 NX9K(contig-if-nve)# source-interface loopback0
C. NX9K(config)# interface loopback0 NX9K(config-if)# ip address 10.10.10.11/32 NX9K(config)# interface tunnel1 NX9K(config-if)# tunnel source loopback0 NX9K(config)# interface ethernet1/1 NX9K(contig-if)# ip unnumbered loopback0
D. NX9K(config)# interface loopback0 NX9K(config-if)# ip address 10.10.10.11/32 NX9K(config)# interface nve1 NX9K(config-if-nve)# source-interface loopback0 NX9K(config)# interface ethernet1/1 NX9K(contig-if)# ip unnumbered loopback0
Question 74
An engineer must perform a software upgrade on a production Cisco Nexus 7000 Series Switch. Before the upgrade activity, the requirement is for all ports to be shut down and routing protocols to terminate gracefully. Which feature must be used to meet these requirements?
A. Switch Profile
B. Service Profile Template
C. Maintenance Mode Profile
D. Configuration Profile
Question 75
DRAG DROP -Refer to the exhibit. An engineer must monitor the Ethernet port and the corresponding VLAN traffic for the hyper4 device. The SW3 device is a Cisco Nexus 7000Series Switch. Drag and drop the code snippets from the right into the boxes in the configuration to meet these requirements.Select and Place:
Question 76
DRAG DROP -Drag and drop the network assurance concepts from the left onto the corresponding benefits on the right.Select and Place:
Question 77
DRAG DROP -An engineer must configure HSPR protocol on two Cisco Nexus 9000 Series Switches running a virtual port channel. In addition, the HSRP implementation must meet these requirements: -It must allow more than 500 groups. -switch1 must act as the primary switch. -Both switches must use a user-defined hardware address.Drag and drop the commands from the right to complete a configuration of the HSRP on the left. The commands are used more than once. Not all commands are used.Select and Place:
Question 78
An engineer must configure OSPFv2 connectivity between a pair of Cisco Nexus switches. The connection between the switches must meet these requirements:Us - unicast for updates. -Use decentralized communication of updates. -Full adjacency between switches.Which configuration is needed to meet these requirements?
A. filter list between the neighbors
B. stub area between the neighbors
C. virtual link between the neighbors
D. interface with a type of p2p network
Question 79
An infrastructure architect is analyzing the deployment type for an application. Several companies must be able to operate the application environment and integrate it with a third-party protocol. The development team also must have maximum control over their development environment, including the operating system used, Python interpreter, and corresponding libraries. Which cloud deployment solution meets these requirements?
A. private cloud Platform as a Service
B. public cloud Storage as a Service
C. hybrid cloud Software as a Service
D. community cloud Infrastructure as a Service Most Voted
Question 80
An engineer is performing an ISSU upgrade on the Cisco MDS 9000 Series Switch. What is the impact on the control plane of the switch?
A. It is down for less than 80 seconds.
B. It remains down for more than 80 seconds but less than 140 seconds.
C. It remains down until the next reboot.
D. It remains up throughout the update.
