Question 61
Refer to the exhibit. An engineer needs to implement streaming telemetry on a Cisco MDS 9000 Series Switch. The requirement is for the show command data to be collected every 30 seconds and sent to receivers. Which command must be added to the configuration to meet this requirement?
A. snsr-grp 200 sample-interval 30000
B. snsr-grp 200 sample-interval 30
C. sensor-grp 200 sample-period 30
D. sensor-grp 200 sample-period 30000
Question 62
An engineer must configure OSPF in the data center. The external routes have already been redistributed into OSPF. The network must meet these criteria:* The data center servers must reach services in the cloud and the services behind the redistributed routes.* The exit point toward the Internet should be propagated only when there is a dynamically learned default route from the upstream router.Which feature is required?
A. stubby area
B. totally stubby area
C. default-information originate Most Voted
D. default-information originate always
Question 63
An engineer must configure a VXLAN routing on a Cisco Nexus 9000 Series Switch. The engineer requires a solution where all the leaf switches have the same gateway MAC and IP addresses. Which configuration set accomplishes this task?
A. NX9K(config)# fabric forwarding anycast-gateway-mac AA:BB:AA:BB:AA:BB NX9K(config)# interface VLAN-interface-name NX9K(config-if)# vrf member vrf-name NX9K(config-if)# fabric forwarding mode anycast-gateway Most Voted
B. NX9K(config)# install feature-set fabric NX9K(config)# feature-set fabric NX9K(config)# fabric forwarding anycast-gateway-mac AA:BB:AA:BB:AA:BB NX9K(config)# interface VLAN-interface-name NX9K(config-if)# fabric forwarding mode anycast-gateway
C. NX9K(config)# install feature-set fabric NX9K(config)# feature-set fabric NX9K(config)# fabric forwarding anycast-gateway-mac AA:BB:AA:BB:AA:BB NX9K(config)# interface VLAN-interface-name NX9K(config-if)# vrf member vrf-name NX9K(config-if)# fabric forwarding mode anycast-gateway
D. NX9K(config)# fabric forwarding anycast-gateway-mac AA:BB:AA:BB:AA:BB NX9K(config)# interface VLAN-interface-name NX9K(config-if)# fabric forwarding mode anycast-gateway
Question 64
An engineer implements an ACI fabric and must implement microsegmentation of endpoints within the same IP subnet using a network-based attribute. The attribute mapping must allow IP subnet independence. Which attribute must be selected?
A. IP
B. tag
C. custom
D. MAC address
Question 65
What is a characteristic of the install all command on the Cisco Nexus Series Switch?
A. automatically checks the image integrity
B. continues the upgrade process if any step in the sequence fails
C. upgrades only certain modules
D. impacts data plane traffic
Question 66
DRAG DROP - An engineer must configure the HSRP protocol to implement redundancy using two Cisco Nexus Series Switches, in addition, me HSRP must meet these requirements:
Question 67
Refer to the exhibit. During a vPC peer switch reload, there is packet loss between the server and the router. Which action must be taken to prevent this behavior during future reloads?
A. Set the routed uplink ports of the Cisco Nexus peers as orphans.
B. Increase the vPC delay restore timer.
C. Disable vPC ARP synchronize on the vPC peers.
D. Decrease the OSPF hello and dead interval timers.
Question 68
A Cisco ACI engineer must configure an access port on a Cisco ACI leaf switch. The access policy should be configured so that it supports L3Out connectivity concurrently with several EPGs that are mapped to this interface with the static port method. How should the access policy be configured?
A. by linking the interface policy group to multiple Attachable Access Entity Profiles
B. with two interface policy groups that are linked to the same interface profile port selector
C. by mapping a single physical domain, mapped to the L3out and EPG interfaces
D. with a single Attachable Access Entity Profile that is linked to the corresponding routed domain and physical domain
Question 69
Refer to the exhibit. An engineer monitors ingress traffic from Host-A and all traffic for VLAN 20 from Host-B. Which configuration must be implemented to monitor and export traffic to Network Analyzer?
A. SW-1(config)# monitor session 5 SW-1(config-monitor)# source interface ethernet 1/2 rx SW-1(config-monitor)# source interface ethernet 1/1 tx SW-1(config-monitor)# source vlan 20 both SW-1(config-monitor)# destination ip 10.10.10.1 SW-1(config-monitor)# no shut
B. SW-1(config)# monitor session 5 type erspan-source SW-1(config-erspan-src)# source interface ethernet 1/2 rx SW-1(config-erspan-src)# source vlan 20 both SW-1(config-erspan-src)# destination ip 10.10.10.1 SW-1(config-erspan-src)# erspan-id 111 SW-1(config-erspan-src)# no shut
C. SW-1(config)# monitor session 5 SW-1(config-monitor)# source interface ethernet 1/2 rx SW-1(config-monitor)# source interface ethernet 1/1 both SW-1(config-monitor)# source vlan 20 both SW-1(config-monitor)# destination interface ethernet 2/1 SW-1(config-monitor)# no shut
D. SW-1(config)# monitor session 5 type erspan SW-1(config-erspan-src)# source interface ethernet 1/2 rx SW-1(config-erspan-src)# source interface ethernet 1/1 both SW-1(config-erspan-src)# destination ip 10.10.10.1 SW-1(config-erspan-src)# mtu 1000 SW-1(config-erspan-src)# no shut
Question 70
Refer to the exhibit. Which action completes the vPC domain implementation?
A. Add the vPC member ports to the vPC channel group. Most Voted
B. Configure the system MAC on the vPC domain.
C. Include the VRF management on the vPC domain.
D. Allow VLANs on the vPC peer link member interfaces.
