An engineer must configure OSPF routing on Cisco Nexus 9000 Series Switches. The IP subnet of the Eth1/2 interfaces for both switches must be advertised viaOSPF. However, these interfaces must not establish OSPF adjacency or send routing updates. The current OSPF adjacency over the interfaces Eth1/1 on SW1 and Eth1/1 on SW2 must remain unaffected. Which configuration must be applied to both Nexus switches to meet these requirements?
A.
B.
C.
D.
Question 52
A network engineer must perform a backup and restore of the Cisco Nexus 5000 Series Switch configuration. The backup must be made to an external backup server. The only protocol permitted between the Cisco Nexus Series switch and the backup server is UDP. The backup must be used when the current working configuration of the switch gets corrupted. Which set of steps must be taken to meet these requirements?
A. 1. Perform a running-config backup to an SFTP server. 2. Copy backup-config from the SFTP server to the running-config file.
B. 1. Perform a startup-config backup to a TFTP server. 2. Copy backup-config from the backup server to the running-config file.
C. 1. Perform a running-config backup to an SCP server. 2. Copy running-config in the boot flash to the running-config file.
D. 1. Perform a startup-config backup to an FTP server. 2. Copy startup-config in the boot flash to the running-config file.
Question 53
Refer to the exhibit. Which command is run from the Guest Shell to set the description on the first five interfaces of the Cisco Nexus switch?
A. [guestshell@guestshell ~]$ for x in {1..5}; dohost "conf t ; interface eth1/$x ; description Server$x";
B. [guestshell@guestshell ~]$ for x in {1..5}; do dohost "conf t ; interface eth1/$x ; description Server$x"; done
C. [guestshell@guestshell ~]$ for x in (1..5); do dohost "conf t"; "interface eth1/$x" ; "description Server$x"; done
D. [guestshell@guestshell ~]$ for x in (1..5); dohost "conf t ; interface eth1/$x ; description Server$x";
Question 54
An engineer must configure multiple EPGs on a single access port in a large Cisco ACI fabric without using VMM integration. The relevant access policies and tenant policies have been created. A single AAEP is used to configure the access ports in the fabric. Which two additional steps must be taken to complete the configuration? (Choose two.)
A. The EPGs must link directly to the corresponding AAEP
B. A contract must be defined between the EPGs
C. The EPGs must be configured as static ports
D. The corresponding bridge domains must be configured in legacy mode
E. The EPGs must be linked to the correct physical domain
Question 55
Several production and development database servers exist in the same EPG and IP subnet. The IT security policy is to prevent connections between production and development. Which attribute must be used to assign the servers to different microsegments?
A. data center
B. VM name
C. IP address
D. VMM domain
Question 56
An environment consists of a Cisco MDS 9000 Series Switch that uses port channels. An engineer must ensure that frames between the source and the destination follow the same links for a specific flow. Subsequent flows are allowed to use a different link. Which load balancing method should be used to accomplish this goal?
A. src-id/dst-id
B. src-dst-oui
C. src-dst-port
D. src-id/dst-id/oxid
Question 57
Refer to the exhibit. An engineer must monitor ingress traffic from SW1 and SW2 port-channel interfaces from SW3. Which configuration must be implemented to accomplish this goal?
Refer to the exhibit. A host with a source address 10.10.10.10 sends traffic to multicast group 239.1.1.1. How do the vPC switches forward the multicast traffic?
A. If multicast traffic is received on Switch1 over the vPC peer-link, the traffic is dropped
B. If multicast traffic is received on Po10 Switch1, the traffic is forwarded out on Po1 and Po20
C. If multicast traffic is received on Po11 Switch2, the traffic is forwarded out only on Po20
D. If multicast traffic is received on Po11 Switch2, the traffic is dropped.
Question 59
A network architect must redesign a data center network based on OSPFv2. The network must perform fast reconvergence between directly connected switches.Which two actions must be taken to meet the requirements? (Choose two.)
A. Set low OSPF hello and DEAD timers.
B. Configure all links on AREA 0.
C. Enable BFD for failure detection.
D. Use OSPF point-to-point links only.
E. Implement a virtual link between the switches.
Question 60
Refer to the exhibit. Which configuration ensures that the Cisco Nexus 7000 Series Switches are the primary devices for LACP?
A. N7K_A(config-vpc-domain)# role priority 1 N7K_B(config-vpc-domain )# role priority 2
B. N7K_A(config-vpc-domain)# system-priority 32768 N7K_B(config-vpc-domain)# system-priority 32768
C. N7K_A(config-vpc-domain)# system-priority 100 N7K_B(config-vpc-domain)# system-priority 200
D. N7K_A(config-vpc-domain)# system-priority 4000 N7K_B(config-vpc-domain)# system-priority 4000 Most Voted
