Win IT Exam with Last Dumps 2023

DRAG DROP -Drag and drop the characteristics from the left onto the protocols they apply to on the right.Select and Place:

Refer to the exhibit. Which set of commands on router R1 allow deterministic translation of private hosts PC1, PC2, and PC3 to addresses in the public space?

A. RouterR1(config)#int f0/0 RouterR1(config)#ip nat inside RouterR1(config)#exit RouterR1(config)#int f0/1 RouterR1(config)#ip nat outside RouterR1(config)#exit RouterR1(config)#access-list 1 10.10.10.0 0.0.0.255 RouterR1(config)#ip nat inside source list 1 interface f0/1 overload

B. RouterR1(config)#int f0/0 RouterR1(config)#ip nat inside RouterR1(config)#exit RouterR1(config)#int f0/1 RouterR1(config)#ip nat outside RouterR1(config)#exit RouterR1(config)#access-list 1 10.10.10.0 0.0.0.255 RouterR1(config)#ip nat pool POOL 155.1.1.101 155.1.1.103 netmask 255.255.255.0 RouterR1(config)#ip nat inside source list 1 pool POOL

C. RouterR1(config)#int f0/0 RouterR1(config)#ip nat inside RouterR1(config)#exit RouterR1(config)#int f0/1 RouterR1(config)#ip nat outside RouterR1(config)#exit RouterR1(config)#ip nat inside source static 10.10.10.101 155.1.1.101 RouterR1(config)#ip nat inside source static 10.10.10.102 155.1.1.102 RouterR1(config)#ip nat inside source static 10.10.10.103 155.1.1.103

D. RouterR1(config)#int f0/0 RouterR1(config)#ip nat outside RouterR1(config)#exit RouterR1(config)#int f0/1 RouterR1(config)#ip nat inside RouterR1(config)#exit RouterR1(config)#ip nat inside source static 10.10.10.101 155.1.1.101 RouterR1(config)#ip nat inside source static 10.10.10.102 155.1.1.102 RouterR1(config)#ip nat inside source static 10.10.10.103 155.1.1.103

Refer to the exhibit. Communication between London and New York is down. Which command set must be applied to the NewYork switch to resolve the issue?

A. NewYork(config)#no interface po1 NewYork(config)#interface range fa0/1-2 NewYork(config-if)#channel-group 1 mode negotiate NewYork(config-if)#end NewYork#

B. NewYork(config)#no interface po1 NewYork(config)#interface range fa0/1-2 NewYork(config-if)#channel-group 1 mode on NewYork(config-if)#end NewYork#

C. NewYork(config)#no interface po1 NewYork(config)#interface range fa0/1-2 NewYork(config-if)#channel-group 1 mode passive NewYork(config-if)#end NewYork#

D. NewYork(config)#no interface po1 NewYork(config)#interface range fa0/1-2 NewYork(config-if)#channel-group 1 mode auto NewYork(config-if)#end NewYork#

Refer to the exhibit. An engineer is configuring an EtherChannel between Switch1 and Switch2 and notices the console message on Switch2. Based on the output, which action resolves this issue?

A. Configure more member ports on Switch1.

B. Configure less member ports on Switch2.

C. Configure the same port channel interface number on both switches.

D. Configure the same EtherChannel protocol on both switches.

Refer to the exhibit. A network engineer configures NAT on R1 and enters the show command to verify the configuration. What does the output confirm?

A. The first packet triggered NAT to add an entry to the NAT table.

B. R1 is configured with NAT overload parameters.

C. A Telnet session from 160.1.1.1 to 10.1.1.10 has been initiated.

D. R1 is configured with PAT overload parameters.

Refer to the exhibit. What is the cause of the log messages?

A. OSPF area change Most Voted

B. MTU mismatch

C. IP address mismatch

D. hello packet mismatch

A network engineer configures BGP between R1 and R2. Both routers use BGP peer group CORP and are set up to use MD5 authentication. This message is logged to the console of router R1:`May 5 39:85:55.469: %TCP-6-BADAUTH` Invalid MD5 digest from 10.10.10.1 (29832) to 10.120.10.1 (179) tebleid -0Which two configurations allow a peering session to form between R1 and R2? (Choose two.)

A. R1(config-router)#neighbor 10.10.10.1 peer-group CORP R1(config-router)#neighbor CORP password Cisco

B. R2(config-router)#neighbor 10.120.10.1 peer-group CORP R2(config-router)#neighbor CORP password Cisco

C. R2(config-router)#neighbor 10.10.10.1 peer-group CORP R2(config-router)#neighbor PEER password Cisco

D. R1(config-router)#neighbor 10.120.10.1 peer-group CORP R1(config-router)#neighbor CORP password Cisco

E. R2(config-router)#neighbor 10.10.10.1 peer-group CORP R2(config-router)#neighbor CORP password Cisco

Refer to the exhibit. An engineer implemented several configuration changes and receives the logging message on Switch1. Which action should the engineer take to resolve this issue?

A. Change Switch2 to switch port mode dynamic auto.

B. Change the VTP domain to match on both switches.

C. Change Switch1 to switch port mode dynamic auto.

D. Change Switch1 to switch port mode dynamic desirable.

DRAG DROP -Drag and drop the characteristics of PIM Dense Mode from the left to the right. Not all options are used.Select and Place:

DRAG DROP -Drag and drop the wireless elements on the left to their definitions on the right.Select and Place: