Win IT Exam with Last Dumps 2023

Refer to the exhibit. A network engineer configures OSPF and reviews the router configuration. Which interface or interfaces are able to establish OSPF adjacency?

A. GigabitEthernet0/0 and GigabitEthernet0/1

B. only GigabitEthernet0/1

C. only GigabitEthernet0/0 Most Voted

D. GigabitEthernet0/1 and GigabitEthernet0/1.40

DRAG DROP -Drag and drop the DHCP messages that are exchanged between a client and an AP into the order they are exchanged on the right.Select and Place:

Which two methods are used by an AP that is trying to discover a wireless LAN controller? (Choose two.)

A. Cisco Discovery Protocol neighbor

B. querying other APs

C. DHCP Option 43

D. broadcasting on the local subnet

E. DNS lookup CISCO-DNA-PRIMARY.localdomain

What is the responsibility of a secondary WLC?

A. It enables Layer 2 and Layer 3 roaming between itself and the primary controller.

B. It registers the LAPs if the primary controller fails. Most Voted

C. It avoids congestion on the primary controller by sharing the registration load on the LAPs.

D. It shares the traffic load of the LAPs with the primary controller.

Refer to the exhibit.Based on the configuration in this WLAN security setting, which method can a client use to authenticate to the network?

A. text string

B. username and password

C. RADIUS token

D. certificate

A client device fails to see the enterprise SSID, but other client devices are connected to it.What is the cause of this issue?

A. The client has incorrect credentials stored for the configured broadcast SSID.

B. The hidden SSID was not manually configured on the client.

C. The broadcast SSID was not manually configured on the client.

D. The client has incorrect credentials stored for the configured hidden SSID.

Which two descriptions of FlexConnect mode for Cisco APs are true? (Choose two.)

A. APs that operate in FlexConnect mode cannot detect rogue APs.

B. When connected to the controller, FlexConnect APs can tunnel traffic back to the controller. Most Voted

C. FlexConnect mode is used when the APs are set up in a mesh environment and used to bridge between each other.

D. FlexConnect mode is a feature that is designed to allow specified CAPWAP-enabled APs to exclude themselves from managing data traffic between clients and infrastructure.

E. FlexConnect mode is a wireless solution for branch office and remote office deployments. Most Voted

Refer to the exhibit. How was spanning-tree configured on this interface?

A. By entering the command spanning-tree portfast trunk in the interface configuration mode. Most Voted

B. By entering the command spanning-tree mst1 vlan 10,20,30,40 in the global configuration mode.

C. By entering the command spanning-tree portfast in the interface configuration mode.

D. By entering the command spanning-tree vlan 10,20,30,40 root primary in the interface configuration mode.

Refer to the exhibit. Rapid PVST+ is enabled on all switches. Which command set must be configured on Switch1 to achieve the following results on port fa0/1? -When a device is connected, the port transitions immediately to a forwarding state. -The interface should not send or receive BPDUs. -If a BPDU is received, it continues operating normally.

A. Switch1(config)# spanning-tree portfast bpdufilter default Switch1(config)# interface f0/1 Switch1(config-if)# spanning-tree portfast

B. Switch1(config)# spanning-tree portfast bpduguard default Switch 1 (config)# interface f0/1 Switch1 (config-if)# spanning-tree portfast

C. Switch1(config)# interface f0/1 Switch1(config-if)# spanning-tree portfast

D. Switch1(config)# interface f0/1 Switch1(config-if)# spanning-tree portfast Switch1 (config-if)# spanning-tree bpduguard enable

Refer to the exhibit. Which configuration change will force BR2 to reach 209.165.201.0/27 via BR1?

A. Set the MED to 1 on PE2 toward BR2 outbound. Most Voted

B. Set the origin to igp on BR2 toward PE2 inbound.

C. Set the weight attribute to 65,535 on BR1 toward PE1.

D. Set the local preference to 150 on PE1 toward BR1 outbound.