Refer to the exhibit. The trunk between Gig1/0/1 of switch SW2 and Gig1/0/1 of switch SW1 is not operational. Which action resolves this issue?
A. Configure both interfaces to nonegotiate and ensure that the switches are in different VTP domains.
B. Configure both interfaces in dynamic auto DTP mode and ensure that the switches are in the same VTP domain.
C. Configure both interfaces in dynamic auto DTP mode and ensure that the switches are in different VTP domains.
D. Configure both interfaces in dynamic desirable DTP mode and ensure that the switches are in the same VTP domain.
Question 182
Refer to the exhibit. Which two facts does the device output confirm? (Choose two.)
A. The device's HSRP group uses the virtual IP address 10.0.3.242.
B. The device is configured with the default HSRP priority.
C. The device sends unicast messages to its peers.
D. The standby device is configured with the default HSRP priority.
E. The device is using the default HSRP hello timer.
Question 183
Refer to the exhibit. Which type of antenna is shown on the radiation patterns?
A. patch
B. dipole
C. omnidirectional
D. Yagi
Question 184
DRAG DROP -Drag and drop the descriptions from the left onto the routing protocol they describe on the right.Select and Place:
Question 185
Refer to the exhibit. All switches are configured with the default port priority value. Which two commands ensure that traffic from PC1 is forwarded over the Gi1/3 trunk port between DSW1 and DSW2? (Choose two.)
A. DSW2(config)#interface gi1/3 Most Voted
B. DSW1(config-if)#spanning-tree port-priority 0
C. DSW2(config-if)#spanning-tree port-priority 128
D. DSW1(config)#interface gi1/3
E. DSW2(config-if)#spanning-tree port-priority 16 Most Voted
Question 186
A company has an existing Cisco 5520 HA cluster using SSO. An engineer deploys a new single Cisco Catalyst 9800 WLC to test new features. The engineer successfully configures a mobility tunnel between the 5520 cluster and 9800 WLC. Clients connected to the corporate WLAN roam seamlessly between access points on the 5520 and 9800 WLC. After a failure on the primary 5520 WLC, all WLAN services remain functional; however, clients cannot roam between the 5520 and 9800 controllers without dropping their connection. Which feature must be configured to remedy the issue?
A. mobility MAC on the 5520 cluster Most Voted
B. mobility MAC on the 9800 WLC
C. new mobility on the 5520 cluster
D. new mobility on the 9800 WLC
Question 187
Refer to the exhibit. Which configuration change ensures that R1 is the active gateway whenever it is in a functional state for the 172.30.110.0/24 network?
A. R2 standby 1 priority 90 standby 1 preempt
B. R2 standby 1 priority 100 standby 1 preempt
C. R1 standby 1 preempt R2 standby 1 priority 90
D. R1 standby 1 preempt R2 standby 1 priority 100
Question 188
A customer has completed the installation of a Wi-Fi 6 greenfield deployment at their new campus. They want to leverage Wi-Fi 6 enhanced speeds on the trusted employee WLAN. To configure the employee WLAN, which two Layer 2 security policies should be used? (Choose two.)
A. WPA2 (AES)
B. 802.1X
C. OPEN
D. WEP
E. WPA (AES)
Question 189
Which two actions, when applied in the LAN network segment, will facilitate Layer 3 CAPWAP discovery for lightweight AP? (Choose two.)
A. Utilize DHCP option 43.
B. Utilize DHCP option 17.
C. Configure an ip helper-address on the router interface.
D. Enable port security on the switch port.
E. Configure WLC IP address on LAN switch
Question 190
Refer to the exhibit. Which action resolves the EtherChannel issue between SW2 and SW3?
A. Configure switchport mode trunk on SW2.
B. Configure switchport nonegotiate on SW3.
C. Configure channel-group 1 mode desirable on both interfaces. Most Voted
D. Configure channel-group 1 mode active on both interfaces.
