Win IT Exam with Last Dumps 2025

Refer to the exhibit. A network engineer started to configure two directly-connected routers as shown.
Which command sequence must the engineer configure on R2 so that the two routers become OSPF neighbors?

A. interface GigabitEthernet0/1
ip ospf 1 area 1 B. router ospf 1
network 192.168.12.1 0.0.0.0 area 1 C. interface GigabitEthernet0/1
ip ospf 1 area 0 D. router ospf 1
network 192.168.12.0 0.0.0.127 area 0

Refer to the exhibit. Router R14 is in the process of being configured.
Which configuration must be used to establish a host route to a PC 10?

A. ip route 10.80.65.10 255.255.255.254 10.80.65.1 B. ip route 10.80.65.10 255.255.255.255 10.73.65.66 C. ip route 10.73.65.66 0.0.0.255 10.80.65.10 D. ip route 10.73.65.66 255.0.0.0 10.80.65.10

Refer to the exhibit.
Which next-hop IP address has the least desirable metric when sourced from R1?

A. 10.10.10.4 B. 10.10.10.5 C. 10.10.10.3 D. 10.10.10.2

Refer to the exhibit. The primary route across Gi0/0 is configured on both routers. A secondary route must be configured to establish connectivity between the workstation networks.
Which command set must be configured to complete this task?

A. R1 -
ip route 172.16.2.0 255.255.255.248 172.16.0.5 110

R2 -
ip route 172.16.1.0 255.255.255.0 172.16.0.6 110 B. R1 -
ip route 172.16.2.0 255.255.255.240 172.16.0.2 113

R2 -
ip route 172.16.1.0 255.255.255.0 172.16.0.1 114
C. R1 -
ip route 172.16.2.0 255.255.255.224 172.16.0.6 111

R2 -
ip route 172.16.1.0 255.255.255.0 172.16.0.5 112 D. R1 -
ip route 172.16.2.0 255.255.255.240 172.16.0.5 89

R2 -
ip route 172.16.1.0 255.255.255.0 172.16.0.6 89

DRAG DROP -Refer to the exhibit. Drag and drop the destination IPs from the left onto the paths to reach those destinations on the right.

Refer to the exhibit.
Which two values does router R1 use to determine the best path to reach destinations in network 1.0.0.0/8? (Choose two.)

A. lowest cost to reach the next hop B. highest administrative distance C. lowest metric D. highest metric E. longest prefix match

Refer to the exhibit. A public IPv6 address must be configured for internet access.
Which command must be configured on the R2 WAN interface to the service provider?

A. ipv6 address fe80::/10 B. ipv6 address 2001:db8:433:37:7710:ffff:ffff:ffff/64 anycast C. ipv6 address 2001:db8:123:45::4/64 D. ipv6 address fe80::260:3EFF:FE11:6770 link-local

DRAG DROP -Refer to the exhibit. Drag and drop the subnet masks from the left onto the corresponding subnets on the right. Not all subnet masks are used.

Refer to the exhibit. A network engineer must configure router R1 with a host route to the server.
Which command must the engineer configure?

A. R1(config)#ip route 10.10.10.10 255.255.255.255 192.168.0.2 B. R1(config)#ip route 10.10.10.0 255.255.255.0 192.168.0.2 C. R1(config)#ip route 0.0.0.0 0.0.0.0 192.168.0.2 D. R1(config)#ip route 192.168.0.2 255.255.255.255 10.10.10.10

Refer to the exhibit. IPv6 is being implemented within the enterprise. The command ipv6 unicast-routing is configured. Interface Gig0/0 on R1 must be configured to provide a dynamic assignment using the assigned IPv6 block.
Which command accomplishes this task?

A. ipv6 address 2001:DB8:FFFF:FCF3::64 link-local B. ipv6 address 2001:DB8:FFFF:FCF3::1/64 C. ipv6 address 2001:DB8:FFFF:FCF3::64 eui-64 D. ipv6 address autoconfig 2001:DB8:FFFF:FCF2::/64