Win IT Exam with Last Dumps 2025

Refer to the exhibit. With which metric does router R1 learn the route to host 172.16.0.202?

A. 90 B. 110 C. 32445 D. 3184439

Refer to the exhibit. A network engineer must configure the link with these requirements:
* Consume as few IP addresses as possible.
* Leave at least two additional useable IP addresses for future growth.
Which set of configurations must be applied?

A. R1(config-if)#ip address 10.10.10.1 255.255.255.252
R2(config-if)#ip address 10.10.10.2 255.255.255.252 B. R1(config-if)#ip address 10.10.10.1 255.255.255.240
R2(config-if)#ip address 10.10.10.12 255.255.255.240 C. R1(config-if)#ip address 10.10.10.1 255.255.255.248
R2(config-if)#ip address 10.10.10.4 255.255.255.248 D. R1(config-if)#ip address 10.10.10.1 255.255.255.0
R2(config-if)#ip address 10.10.10.5 255.255.255.0

DRAG DROP -Drag and drop the device behaviors from the left onto the matching HSRP state on the right.

Refer to the exhibit. A static route must be configured on R86 to forward traffic for the 172.16.34.0/29 network, which resides on R14.
Which command must be used to fulfill the request?

A. ip route 10.73.65.65 255.255.255.248 172.16.34.0 B. ip route 172.16.34.0 255.255.255.248 10.73.65.65 C. ip route 172.16.34.0 0.0.0.7 10.73.65.64 D. ip route 172.16.34.0 255.255.224.0 10.73.65.66

Refer to the exhibit. An engineer must configure a floating static route on an external EIGRP network. The destination subnet is the /29 on the LAN interface of R86.
Which command must be executed on R14?

A. ip route 10.80.65.0 255.255.248.0 10.73.65.66 1 B. ip route 10.80.65.0 255.255.255.240 fa0/1 89 C. ip route 10.80.65.0 255.255.255.248 10.73.65.66 171 D. ip route 10.73.65.66 0.0.0.224 10.80.65.0 255

DRAG DROP -

Refer to the exhibit. An IPv6 address must be obtained automatically on the LAN interface on R1.
Which command must be implemented to accomplish the task?

A. ipv6 address autocontig B. ipv6 address dhcp C. ipv6 address fe80::/10 D. ipv6 address 2001:db8:d8d2:1008:4332:45:0570::/64

Refer to the exhibit. A network engineer is updating the configuration on router R1 to connect a new branch office to the company network. R2 has been configured correctly.
Which command must the engineer configure so that devices at the new site communicate with the main office?

A. ip route 172.25.25.1 255.255.255.255 g0/2 B. ip route 172.25.25.0 255.255.255.0 192.168.2.2 C. ip route 172.25.25.0 255.255.255.0 192.168.2.1 D. ip route 172.25.25.1 255.255.255.255 g0/1

A network engineer must migrate a router loopback interface to the IPv6 address space. If the current IPv4 address of the interface is 10.54.73.1/32, and the engineer configures IPv6 address 0:0:0:0:0:ffff:a36:4901, which prefix length must be used?

A. /64 B. /96 C. /124 D. /128

A Cisco engineer notices that two OSPF neighbors are connected using a crossover Ethernet cable. The neighbors are taking too long to become fully adjacent.
Which command must be issued under the interface configuration on each router to reduce the time required for the adjacency to reach the FULL state?

A. ip ospf dead-interval 40 B. ip ospf network broadcast C. ip ospf priority 0 D. ip ospf network point-to-point