Question 21
What are two capabilities of the Cisco Network Assurance Engine? (Choose two.)
A. It validates that devices comply with network security policies.
B. It predicts the impact of changes to the network.
C. It predicts the network load on a data center.
D. It ensures that network performance meets an SLA.
E. It verifies the speed of network packet flows by using telemetry.
Question 22
What is an advantage of streaming telemetry over SNMP?
A. on-change traps sent to a receiver
B. periodic push-based subscription messages
C. periodic polling of the device status
D. MD5-based authentication on polling
Question 23
APIC EPG Resolution Immediacy is set to "Immediate".Which statement is true about the Deployment Immediacy for VMM domains associated to EPGs?
A. If "On demand" is selected, the policy is programmed in the hardware only when the first packet is received through the data path.
B. If "Immediate" is selected, the policy is programmed in the hardware as soon as the leaf is booted.
C. The "Immediate" and "On demand" options require a port group to be created on the VDS.
D. If "On demand" is selected, the policy is programmed in the hardware only when the APIC detects a VM created in the EPG.
Question 24
Refer to the exhibit. All switches are configured with the default OSPF priority. Which configuration should be applied to ensure that the SW2 Cisco Nexus switch controls the LSA floods and advertises the network to the remaining nodes in the OSPFv2 area?
A. SW2# configure terminal SW2 (config)# interface ethernet 1/1 SW2 (config-if)# ip ospf priority 255
B. SW2# configure terminal SW2 (config)# interface ethernet 1/1 SW2 (config-if)# ip ospf priority 1
C. SW2# configure terminal SW2 (config)# router ospf 1 SW2 (config-router)# router-id 10.10.10.22
D. SW2# configure terminal SW2 (config)# interface ethernet 1/1 SW2 (config-if)# ip ospf priority 0
Question 25
DRAG DROP -Refer to the exhibit. In a bidirectional PIM network using Phantom RP as an RP redundancy mechanism, two Cisco NX-OS routers have these requirements: -R1 must be the active RP. -R2 must be the backup RP that is used only if R1 is not reachable.Drag and drop the configuration steps to complete the configuration for Router 2. Not all configuration steps are used.Select and Place:
Question 26
An engineer must configure a Nexus 7000 series switch for HSRP on VLAN 100. When fully functional, the router must be the active master. Which set of commands must be used to implement the scenario?
A. feature hsrp interface vlan100 ip address 10.1.1.2 255.255.255.0 priority 255 preempt hsrp version 2 hsrp 1000 ip 10.1.1.1
B. feature-set hsrp interface vlan100 ip address 10.1.1.2 255.255.255.0 priority 20 preempt hsrp version 2 hsrp 1000 ip 10.1.1.1
C. feature-set hsrp interface vlan100 ip address 10.1.1.2 255.255.255.0 priority 80 preempt hsrp version 2 hsrp 1000 ip 10.1.1.1
D. feature hsrp interface vlan100 ip address 10.1.1.2 255.255.255.0 priority 240 preempt hsrp version 2 hsrp 1000 ip 10.1.1.1
Question 27
Which MAC address is an HSRP version 2?
A. 3842.4250.0000
B. 0000.0C07.AC1H
C. 0000.0C9F.F0C8
D. 0100.5E7F.FFFF
Question 28
Refer to the exhibit. Which VLANs are capable to be assigned on vPC interfaces?
A. 100-102
B. 100-103
C. 100-104
D. 100-105
Question 29
An engineer need to implement a solution that prevents loops from occurring accidentally by connecting a switch to interface Ethernet1/1. The port is designated to be used for host connectivity. Which configuration should be implemented?
A. switch# configure terminal switch(config)# interface Ethernet1/1 switch(config-if)# spanning-tree bpduguard enable
B. switch# configure terminal switch(config)# interface Ethernet1/1 switch(config-if)# spanning-tree guard loop
C. switch# configure terminal switch(config)# interface Ethernet1/1 switch(config-if)# spanning-tree loopguard default
D. switch# configure terminal switch(config)# interface Ethernet1/1 switch(config-if)# spanning-tree bpdufilter enable
Question 30
A network engineer repeatedly saves a configuration on Catalyst switches to NVRAM using the write memory command. Which action should be taken to implement the same action on Nexus switches?
A. Use the alias command to use the write memory command.
B. Use the wri command to use the copy running-config startup-config command.
C. Use the exit command to leave the configuration mode and save the configuration automatically.
D. Use the write memory command to save the configuration.
