Win IT Exam with Last Dumps 2023


Cisco 350-501 Exam

Page 9/26
Viewing Questions 81 90 out of 253 Questions
34.62%

Question 81
Refer to the exhibit. Which task completes the configuration?
Image 350-501_81Q.png related to the Cisco 350-501 Exam
A. Specify the local-as value in the neighbor statement
B. Specify the source interface in the neighbor statement
C. Specify the maximum number of prefixes that R1 receives from neighbor 192.168.1.2
D. Specify the activate neighbor 192.168.1.2 under the IPv4 address family

Question 82
Refer to the exhibit. A network engineer is implementing OSPF multiarea. Which command on interface G0/1 resolves adjacency issues in the new area?
Image 350-501_82Q.png related to the Cisco 350-501 Exam
A. ip ospf network point-to-point
B. ip ospf network broadcast
C. ip ospf network non-broadcast
D. ip ospf network point-to-multipoint

Question 83
Refer to the exhibit. An engineer is configuring router R1 for OSPFv3 as shown. Which additional configuration must be performed so that the three active interfaces on the router will advertise routes and participate in OSPF IPv6 processes?
Image 350-501_83Q.png related to the Cisco 350-501 Exam
A.
Image 350-501_83QA.png related to the Cisco 350-501 Exam
B.
Image 350-501_83QB.png related to the Cisco 350-501 Exam
C.
Image 350-501_83QC.png related to the Cisco 350-501 Exam
D.
Image 350-501_83QD.png related to the Cisco 350-501 Exam

Question 84
Refer to the exhibit. While troubleshooting a connectivity issue on router R2, a network engineer with an employee id: 1234:44:876 notices that although it detects three OSPF links from R1, the OSPF prefixes are missing from the routing table. What is the reason for the problem?
Image 350-501_84Q.png related to the Cisco 350-501 Exam
A. The serial interfaces have different MTUs
B. Both loopback interfaces on R1 are configured as stub
C. The subnet masks on the serial interfaces are mismatched
D. The R2 Serial1/0 interface is configured with an IP address, but the R1 Serial1/0 interface is unnumbered

Question 85
DRAG DROP -Refer to the exhibit. An engineer wants to determine which paths are best, second best, third best, and fourth best. Drag and drop the peer addresses on the left to the corresponding BGP best-path selection order on the right.Select and Place:
Image 350-501_85Q.png related to the Cisco 350-501 Exam
Image 350-501_85R.png related to the Cisco 350-501 Exam

Question 86
Refer to the exhibit. While troubleshooting the OSPF adjacency between routers R1 and R2, an engineer noticed that both routers are stuck in the EXCHANGE/EXSTART state. What should the engineer fix to solve the ongoing issue?
Image 350-501_86Q.png related to the Cisco 350-501 Exam
A. match OSPF network types
B. match IPv4 addresses
C. match MTU values
D. match OSPF areas

Question 87
Refer to the exhibit. A network engineer is implementing a standard customer route-policy on router ASBR1 with these requirements: -It must accept only customer-assigned prefixes. -It must preserve customer-advertised BGP communities. -It must set the local-preference to 110 for all prefixes.It must attach the ORIGINATION-PE and LOCAL-CITY communities to all accepted prefixes.Which route policy must the engineer implement on ASBR1 to satisfy the requirements?
Image 350-501_87Q.png related to the Cisco 350-501 Exam
A.
Image 350-501_87QA.jpg related to the Cisco 350-501 Exam
B.
Image 350-501_87QB.jpg related to the Cisco 350-501 Exam
C.
Image 350-501_87QC.jpg related to the Cisco 350-501 Exam
D.
Image 350-501_87QD.jpg related to the Cisco 350-501 Exam

Question 88
What are two factors to consider when implementing NSR High Availability on an MPLS PE router? (Choose two.)
A. It requires all PE-CE sessions to support NSR
B. It requires routing protocol extensions
C. It consumes more memory and CPU resources than NSF
D. It operates normally without NSR support on the PE peers
E. It cannot sync state information across redundant RPs

Question 89
Refer to the exhibit. A network operator needs to shut down interface Gi0/0/0/2 for maintenance. What occurs to the interface states of Gi0/0/0/0 and Gi0/0/0/1?
Image 350-501_89Q.png related to the Cisco 350-501 Exam
A. Gi0/0/0/1 and Gi0/0/0/0 become active
B. Gi0/0/0/1 and Gi0/0/0/0 remain standby
C. Gi0/0/0/0 becomes active; Gi0/0/0/1 remains standby
D. Gi0/0/0/1 becomes active; Gi0/0/0/0 remains standby

Question 90
Refer to the exhibit. When the Link Aggregation configuration router is running on Cisco IOS XR Software, which LACP interface configuration is needed to add the interface to the bundle?
Image 350-501_90Q.png related to the Cisco 350-501 Exam
A.
Image 350-501_90QA.png related to the Cisco 350-501 Exam
B.
Image 350-501_90QB.png related to the Cisco 350-501 Exam
C.
Image 350-501_90QC.png related to the Cisco 350-501 Exam
D.
Image 350-501_90QD.png related to the Cisco 350-501 Exam