Win IT Exam with Last Dumps 2025

Refer to the exhibit
Which configuration is required to summarize the Area 2 networks that are advertised to Area 0?

A. RouterB(config)# router ospf 1 RouterB(config-router)# area 2 range 192.168.36.0 255.255.252.0

B. RouterB(config)# router ospf 1 RouterB(config-router)# network 192.168.38.0 255.255.255.0

C. RouterB(config)# router ospf 1 RouterB(config-router)# network 192.168.38.0 255.255.252.0

D. RouterB(config)# router ospf 1 RouterB(config-router)# area 2 range 192.168.36.0 255.255.255.0

Based on the router's API output in JSON format below, which Python code will display the value of the "role" key?

A.

B.

C.

D.

What is the recommended minimum SNR for voice applications on wireless networks?

A. 10

B. 15

C. 20

D. 25

Refer to the exhibit. What are two results of the NAT configuration? (Choose two.)

A. Packets with a destination of 200.1.1.1 are translated to 10.1.1.1 or .2, respectively.

B. A packet that is sent to 200 1.1.1 from 10.1.1.1 is translated to 209.165.201.1 on R1.

C. R1 is performing NAT for inside addresses and outside address.

D. R1 looks at the destination IP address of packets entering S0/0 and destined for inside hosts.

E. R1 processes packets entering E0/0 and S0/0 by examining the source IP address.

A network engineer must configure a switch to allow remote access for all feasible protocols Only a password must be requested for device authentication and all idle sessions must be terminated in 30 minutes
Which configuration must be applied?

A. line vty 0 15 password cisco transport input telnet ssh exec-timeout 30 0

B. line vty 0 15 password cisco transport input all exec-timeout 0 30

C. username cisco privilege 15 cisco line vty 0 15 transport input telnet ssh login local exec-timeout 0 30

D. line console 0 password cisco exec-timeout 30 0

Refer to the exhibit. An engineer configures a trunk between SW1 and SW2 but tagged packets are not passing
Which action fixes the issue?

A. Configure SW1 with dynamic auto mode on interface FastEthernet0/1.

B. Configure the native VLAN to be the same VLAN on both switches on interface FastEthernet0/1.

C. Configure SW2 with encapsulation dot1q on interface FastEthernet0/1.

D. Configure FastEthernet0/1 on both switches for static trunking.

When does a Cisco StackWise primary switch lose its role?

A. when a switch with a higher priority is added to the stack

B. when a stack member fails

C. when the priority value of a stack member is changed to a higher value

D. when the stack primary is reset

Refer to the exhibit. A network engineer troubleshoots an issue with the port channel between SW1 and SW2
Which command resolves the issue?

A. SW2(config-if)#switchport mode trunk

B. SW1(config-if)#channel-group 10 mode active

C. SW1(config-if)#channel-group 10 mode desirable

D. SW2(config-if)#channel-group 10 mode on

DRAG DROP -Drag and drop the automation characteristics from the left onto the appropriate tools on the right.
Select and Place:

How do stratum levels relate to the distance from a time source?

A. Stratum 0 devices are connected directly to an authoritative time source.

B. Stratum 1 devices are connected directly to an authoritative time source.

C. Stratum 15 devices are connected directly to an authoritative time source.

D. Stratum 15 devices are an authoritative time source.