Question 121
Refer to the exhibit.Which IP address becomes the active next hop for 192.168.102.0/24 when 192.168.101.2 fails?
A. 192.168.101.10
B. 192.168.101.14
C. 192.168.101.6
D. 192.168.101.18
Question 122
Which PAgP mode combination prevents an EtherChannel from forming?
A. auto/desirable
B. desirable/desirable
C. desirable/auto
D. auto/auto
Question 123
If a VRRP master router fails, which router is selected as the new master router?
A. router with the lowest priority
B. router with the highest priority
C. router with the highest loopback address
D. router with the lowest loopback address
Question 124
Which two mechanisms are available to secure NTP? (Choose two.)
A. IPsec
B. IP prefix list-based
C. encrypted authentication
D. TACACS-based authentication
E. IP access list-based
Question 125
In OSPF, which LSA type is responsible for pointing to the ASBR router?
A. type 1
B. type 2
C. type 3
D. type 4
Question 126
Refer to the exhibit.VLANs 50 and 60 exist on the trunk links between all switches. All access ports on SW3 are configured for VLAN 50 and SW1 is the VTP server.Which command ensures that SW3 receives frames only from VLAN 50?
A. SW1(config)#vtp mode transparent
B. SW3(config)#vtp mode transparent
C. SW2(config)#vtp pruning
D. SW1(config)#vtp pruning
Question 127
Which First Hop Redundancy Protocol maximizes uplink utilization and minimizes the amount of configuration that is necessary?
A. GLBP
B. HSRP v2
C. VRRP
D. HSRP v1
Question 128
Refer to the exhibit.Which configuration establishes EBGP neighborship between these two directly connected neighbors and exchanges the loopback network of the two routers through BGP?
A. R1(config)#router bgp 1 R1(config-router)#neighbor 192.168.10.2 remote-as 2 R1(config-router)#network 10.1.1.0 mask 255.255.255.0 R2(config)#router bgp 2 R2(config-router)#neighbor 192.168.10.1 remote-as 1 R2(config-router)#network 10.2.2.0 mask 255.255.255.0
B. R1(config)#router bgp 1 R1(config-router)#neighbor 10.2.2.2 remote-as 2 R1(config-router)#network 10.1.1.0 mask 255.255.255.0 R2(config)#router bgp 2 R2(config-router)#neighbor 10.1.1.1 remote-as 1 R2(config-router)#network 10.2.2.0 mask 255.255.255.0
C. R1(config)#router bgp 1 R1(config-router)#neighbor 192.168.10.2 remote-as 2 R1(config-router)#network 10.0.0.0 mask 255.0.0.0 R2(config)#router bgp 2 R2(config-router)#neighbor 192.168.10.1 remote-as 1 R2(config-router)#network 10.0.0.0 mask 255.0.0.0
D. R1(config)#router bgp 1 R1(config-router)#neighbor 10.2.2.2 remote-as 2 R1(config-router)#neighbor 10.2.2.2 update-source lo0 R1(config-router)#network 10.1.1.0 mask 255.255.255.0 R2(config)#router bgp 2 R2(config-router)#neighbor 10.1.1.1 remote-as 1 R2(config-router)#neighbor 10.1.1.1 update-source lo0 R2(config-router)#network 10.2.2.0 mask 255.255.255.0
Question 129
Refer to the exhibit.Which type of antenna do the radiation patterns present?
A. Yagi
B. patch
C. omnidirectional
D. dipole
Question 130
Which reason could cause an OSPF neighborship to be in the EXSTART/EXCHANGE state?
A. mismatched OSPF link costs
B. mismatched OSPF network type
C. mismatched areas
D. mismatched MTU size
