Win IT Exam with Last Dumps 2025

A network engineer starts to implement a new wireless LAN by configuring the authentication server and creating the dynamic interface. What must be performed next to complete the basic configuration?

A. Create the new WLAN and bind the dynamic interface to it. B. Configure high availability and redundancy for the access points. C. Enable Telnet and RADIUS access on the managoment interface. D. Install the management interface and add the management IP.

Refer to the exhibit. An architect is managing a wireless network with APs from several branch offices connecting to the WLC in the data center. There is a new requirement for a single WLAN to process the client data traffic without sending it to the WLC.
Which action must be taken to complete the request?

A. Enable local HTTP profiling. B. Enable FlexConnect Local Switching. C. Enable local DHCP Profiling. D. Enable Disassociation Imminent.

Which command configures the Cisco WLC to prevent a serial session with the WLC CLI from being automatically logged out?

A. config sessions maxsessions 0 B. config serial timeout 9600 C. config serial timeout 0 D. config sessions timeout 0

What is an advantage of using auto mode versus static mode for power allocation when an access point is connected to a PoE switch port?

A. Power policing is enabled at the same time. B. The default level is used for the access point. C. All four pairs of the cable are used. D. It detects the device is a powered device.

Refer to the exhibit. Wireless LAN access must be set up to force all clients from the NA WLAN to authenticate against the local database. The WLAN is configured for local EAP authentication. The time that users access the network must not be limited.
Which action completes this configuration?

A. Check the Guest User Role check box. B. Uncheck the Guest User check box. C. Set the Lifetime (seconds) value to 0. D. Clear the Lifetime (seconds) value.

DRAG DROP -Drag and drop the WLAN components from the left onto the correct descriptions on the right.

Refer to the exhibit. A Cisco WLC administrator is creating a new wireless network with enhanced SSID security. The new network must operate at 2.4 Ghz with 54 Mbps of throughput.
Which set of tasks must the administrator perform to complete the configuration?

A. Uncheck the Broadcast SSID check box and set the Radio Policy to 802.11a/g only. B. Check the Broadcast SSID check box and set the Radio Policy to 802.11g only. C. Uncheck the Broadcast SSID check box and set the Radio Policy to 802.11g only. D. Check the Broadcast SSID check box and set the Radio Policy to 802.11a only.

Refer to the exhibit. The SW1 and SW2 Gi0/0 ports have been preconfigured. An engineer is given these requirements:
* Allow all PCs to communicate with each other at Layer 3.
* Configure untagged traffic to use VLAN 5.
* Disable VLAN 1 from being used.

Which configuration set meets these requirements?

A. B. C. D.

Refer to the exhibit. How must router A be configured so that it only sends Cisco Discovery Protocol information to router C?

A. #config t

Router A (config)#no cdp run -
Router A (config)#interface gi0/0/1

Router A (config-if)#cdp enable - B. #config t

Router A (config)#cdp run -
Router A (config)#interface gi0/0/0
Router A (config-if)#no cdp enable C. #config t -

Router A (config)#cdp run -
Router A (config)#interface gi0/0/1

Router A (config-if)#cdp enable - D. #config t

Router A (config)#cdp run -
Router A (config)#interface gi0/0/0
Router A (config-if)#cdp enable

Refer to the exhibit. An administrator must turn off the Cisco Discovery Protocol on the port configured with address last usable address in the 10.0.0.0/30 subnet.
Which command set meets the requirement?

A. interface gi0/1
no cdp enable B. interface gi0/0
no cdp run C. interface gi0/0
no cdp advertise-v2 D. interface gi0/1
clear cdp table