Win IT Exam with Last Dumps 2025

Refer to the exhibit. All traffic enters the CPE router from interface Serial0/3 with an IP address of 192.168.50.1. Web traffic from the WAN is destined for a LAN network where servers are load-balanced. An IP packet with a destination address of the HTTP virtual IP of 192.168.1.250 must be forwarded. Which routing table entry does the router use?

A. 192.168.1.0/24 via 192.168.12.2 B. 192.168.1.128/25 via 192.168.13.3 C. 192.168.1.192/26 via 192.168.14.4 D. 192.168.1.224/27 via 192.168.15.5

Refer to the exhibit. An engineer assumes a configuration task from a peer. Router A must establish an OSPF neighbor relationship with neighbor 172.1.1.1. The output displays the status of the adjacency after 2 hours. What is the next step in the configuration process for the routers to establish an adjacency?

A. Configure router A to use the same MTU size as router B. B. Configure a point-to-point link between router A and router B. C. Set the router B OSPF ID to the same value as its IP address. D. Set the router B OSPF ID to a nonhost address.

Refer to the exhibit. Which two configurations must the engineer apply on this network so that R1 becomes the DR? (Choose two.)

A. R3(config)#interface fastethernet 0/0 R3(config-if)#ip ospf priority 0 B. R1(config)#router ospf 1 R1(config-router)#router-id 192.168.100.1 C. R1(config)#interface fastethernet 0/0 R1(config-if)#ip ospf priority 200 D. R1(config)#interface fastethernet 0/0 R1(config-if)#ip ospf priority 0 E. R3(config)#interface fastethernet 0/0 R3(config-if)#ip ospf priority 200

Refer to the exhibit. Which command configures OSPF on the point-to-point link between routers R1 and R2?

A. router-id 10.0.0.15 B. neighbor 10.1.2.0 cost 180 C. network 10.0.0.0 0.0.0.255 area 0 D. ip ospf priority 100

Refer to the exhibit. A network engineer is in the process of establishing IP connectivity between two sites. Routers R1 and R2 are partially configured with IP addressing. Both routers have the ability to access devices on their respective LANs. Which command set configures the IP connectivity between devices located on both LANs in each site?

A. R1 ip route 192.168.1.1 255.255.255.0 GigabitEthernet0/1 R2 ip route 10.1.1.1 255.255.255.0 GigabitEthernet0/1 B. R1 ip route 192.168.1.0 255.255.255.0 GigabitEthernet0/0 R2 ip route 10.1.1.1 255.255.255.0 GigabitEthernet0/0 C. R1 ip route 0.0.0.0 0.0.0.0 209.165.200.225 R2 ip route 0.0.0.0 0.0.0.0 209.165.200.226 D. R1 ip route 0.0.0.0 0.0.0.0 209.165.200.226 R2 ip route 0.0.0.0 0.0.0.0 209.165.200.225

Refer to the exhibit. Which next-hop IP address does Router1 use for packets destined to host 10.10.13.158?

A. 10.10.10.9 B. 10.10.10.5 C. 10.10.11.2 D. 10.10.12.2

Refer to the exhibit. Packets received by the router from BGP enter via a serial interface at 209.165.201.1. Each route is present within the routing table. Which interface is used to forward traffic with a destination IP of 10.1.1.19?

A. F0/0 B. F0/1 C. F0/4 D. F0/3

Refer to the exhibit. Which route must be configured on R1 so that OSPF routing is used when OSPF is up, but the server is still reachable when OSPF goes down?

A. ip route 10.1.1.10 255.255.255.255 gi0/0 125 B. ip route 10.1.1.0 255.255.255.0 172.16.2.2 100 C. ip route 10.1.1.0 255.255.255.0 gi0/1 125 D. ip route 10.1.1.10 255.255.255.255 172.16.2.2 100

Refer to the exhibit. Which prefix did router R1 learn from internal EIGRP?

A. 192.168.3.0/24 B. 192.168.1.0/24 C. 172.16.1.0/24 D. 192.168.2.0/24

DRAG DROP -Drag and drop the AAA terms from the left onto the descriptions on the right.
Select and Place: