Win IT Exam with Last Dumps 2025

An engineer configured an OSPF neighbor as a designated router. Which state verifies the designated router is in the proper mode?

A. Init B. 2-way C. Exchange D. Full

Refer to the exhibit. Which route does R1 select for traffic that is destined to 192.168.16.2?

A. 192.168.16.0/21 B. 192.168.16.0/24 C. 192.168.16.0/26 D. 192.168.16.0/27

Refer to the exhibit. If configuring a static default route on the router with the ip route 0.0.0.0 0.0.0.0 10.13.0.1 120 command, how does the router respond?

A. It starts sending traffic without a specific matching entry in the routing table to GigabitEthernet0/1. B. It immediately replaces the existing OSPF route in the routing table with the newly configured static route. C. It starts load-balancing traffic between the two default routes. D. It ignores the new static route until the existing OSPF default route is removed.

Refer to the graphic. R1 is unable to establish an OSPF neighbor relationship with R3. What are possible reasons for this problem? (Choose two.)

A. All of the routers need to be configured for backbone Area 1. B. R1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3. C. A static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established. D. The hello and dead interval timers are not set to the same values on R1 and R3. E. EIGRP is also configured on these routers with a lower administrative distance. F. R1 and R3 are configured in different areas.

When the active router in a VRRP group fails, which router assumes the role and forwards packets?

A. forwarding B. standby C. backup D. listening

What is the purpose of using First Hop Redundancy Protocol on a specific subnet?

A. forwards multicast hello messages between routers B. sends the default route to the hosts on a network C. ensures a loop-free physical topology D. filters traffic based on destination IP addressing

Refer to the exhibit. Which configuration issue is preventing the OSPF neighbor relationship from being established between the two routers?

A. R1 has an incorrect network command for interface Gi1/0. B. R2 should have its network command in area 1. C. R1 interface Gi1/0 has a larger MTU size. D. R2 is using the passive-interface default command.

Refer to the exhibit. When router R1 is sending traffic to IP address 10.56.192.1, which interface or next hop address does it use to route the packet?

A. 10.56.0.1 B. 0.0.0.0/0 C. Vlan57 D. 10.56.128.19

Refer to the exhibit. Routers R1 and R3 have the default configuration. The router R2 priority is set to 99. Which commands on R3 configure it as the DR in the 10.0.4.0/24 network?

A. R3(config)#interface Gig0/0 R3(config-if)#ip ospf priority 100 B. R3(config)#interface Gig0/0 R3(config-if)#ip ospf priority 1 C. R3(config)#interface Gig0/1 R3(config-if)#ip ospf priority 0 D. R3(config)#interface Gig0/1 R3(config-if)#ip ospf priority 100

Refer to the exhibit. A network engineer must configure R1 so that it sends all packets destined to the 10.0.0.0/24 network to R3, and all packets destined to PC1 to R2. Which configuration must the engineer implement?

A. R1(config)#ip route 10.0.0.0 255.255.255.0 172.16.0.2 R1(config)#ip route 10.0.0.5 255.255.255.255 192.168.0.2 B. R1(config)#ip route 10.0.0.0 255.255.0.0 172.16.0.2 R1(config)#ip route 10.0.0.5 255.255.255.255 192.168.0.2 C. R1(config)#ip route 10.0.0.0 255.255.255.0 192.168.0.2 R1(config)#ip route 10.0.0.5 255.255.255.255 172.16.0.2 D. R1(config)#ip route 10.0.0.0 255.255.0.0 192.168.0.2 R1(config)#ip route 10.0.0.5 255.255.255.0 172.16.0.2