Question 141
A network engineer is deploying a Cisco All-Flash HyperFlex solution. Which local storage configuration is required for the operating system and persistent logging?
A. one solid state drive
B. two SATA drives
C. one SATA drive
D. two solid state drives
Question 142
DRAG DROP -Drag and drop the fields for configuring a full state backup file of the Cisco UCS Manager from the left onto the descriptions on the right.Select and Place:
Question 143
An engineer configures an Intersight Virtual Appliance and must claim over 200 targets. The engineer starts the Claim New Target Procedure. The engineer has prepared this initial comma-separated value file to provision the targets:UCSFI,10.1.1.3,user-1,pwd5516b917IMC,10.1.1.5/26,user-2,pwdc65b1c43fHX,10.1.2.1/30,user-3,pwd39913690UCSD,1.1.1.1.user-4,pwd5003e9d5 -Which information must be included in the comma-separated value file to provision the targets?
A. target type, hostname or IP address, user name, password
B. __cpLocation, address, name, password
C. FQDN, AD name, IP address, email
D. certificate, user name, password, email
Question 144
Which component is disrupted when the Cisco Integrated Management Controller is upgraded on a Cisco UCS Series Server?
A. SAN traffic
B. Cisco UCS Manager
C. KVM sessions Most Voted
D. data traffic
Question 145
Which two configuration settings are available in the Cisco UCS Firmware Auto Sync Server policy? (Choose two.)
A. Immediate Action
B. User Notification
C. User Acknowledge
D. Delayed Action
E. No Action
Question 146
A Cisco Nexus 9000 Series Switch experiences a startup configuration corruption. The engineer must implement a procedure to recover the backup configuration file from the switch. Which command set must be used?
A. 1. Clear the current configuration of the switch 2. Restart the device 3. Copy a previously saved configuration file to the running-configuration 4. Copy the running-configuration to the startup configuration
B. 1. Clear the current configuration of the switch 2. Restart the device 3. Copy the running configuration to the startup configuration 4. Copy a previously saved configuration file to the running configuration
C. 1. Copy the running-configuration to the startup configuration 2. Clear the current configuration of the switch 3. Restart the device 4. Copy a previously saved configuration file to the running configuration
D. 1. Restart the device 2. Copy the running-configuration file to a remote server 3. Clear the current configuration of the switch 4. Copy the running configuration to the startup configuration
Question 147
An engineer configures the properties of a Cisco UCS Cisco Integrated Management Controller network adapter for a standalone Cisco C-Series Server. TheFailback Timeout in the vNIC was set to 600. When the failure occurs, the secondary interfaces must be used and then failback when the primary interface becomes available again. Which action must be taken to meet these requirements?
A. Set default VLAN on the adapters.
B. Increase CoS to 6.
C. Enable Uplink Failover.
D. Disable VNTAG mode.
Question 148
An engineer must perform a backup operation of the Cisco UCS system. The backup must be transferred to a secure __cpLocation using UDP and must contain information about VLANs, VSANs, and other policies. Also, the operations team requires the backup file to be in a human-readable format. Which configuration set meets these requirements?
A. Type: All configuration Protocol: FTP
B. Type: Full state Protocol: SFTP
C. Type: Logical configuration Protocol: TFTP
D. Type: System configuration Protocol: SCP
Question 149
When deploying a Cisco HyperFlex edge with a pair of switches, what is the minimum number of interfaces in trunk mode required on each HX node?
A. 1
B. 2
C. 4
D. 6
Question 150
What is a benefit of independent resource scaling in Cisco HyperFlex hybrid architecture?
A. remote booting of converged servers
B. flexible expansion of compute, caching, and capacity
C. multivendor converged node hardware support
D. support for compute nodes with third-party storage
