Win IT Exam with Last Dumps 2024

Refer to the exhibit. The network engineer who manages ASN 65001 is troubleshooting suboptimal routing to the 198.18.15.0/24 prefix. According to the network requirements:

A. configure terminal route-policy ASN65001-SPECIFIC-OUT if destination in (198.18.15.0/25) then set community (no-export, peeras:65001) done endif if destination in (198.18.15.0/24) then prepend as-path 65001 3 done endif drop end-policy ! router bgp 65001 neighbor 100.65.0.1 address-family ipv4 unicast route-policy ASN65001-SPECIFIC-OUT out end

B. configure terminal route-policy ASN65001-SPECIFIC-OUT if destination in (198.18.15.0/25) then set community (internal, peeras:65001) done endif if destination in (198.18.15.0/24) then done endif drop end-policy ! router bgp 65001 neighbor 100.65.0.1 address-family ipv4 unicast route-policy ASN65001-SPECIFIC-OUT out end

C. configure terminal route-policy ASN65001-SPECIFIC-OUT if destination in (198.18.15.0/25) then set community (no-advertise, peeras:65001) done endif if destination in (198.18.15.128/25) then prepend as-path 65001 3 done endif drop end-policy ! router bgp 65001 neighbor 100.65.0.1 address-family ipv4 unicast route-policy ASN65001-SPECIFIC-OUT out end

D. configure terminal route-policy ASN65001-SPECIFIC-OUT if destination in (198.18.15.0/25) then set community (no-export, peeras:65001) done endif if destination in (198.18.15.128/25) then prepend as-path 65001 3 done endif drop end-policy ! router bgp 65001 neighbor 100.65.0.1 address-family ipv4 unicast route-policy ASN65001-SPECIFIC-OUT in end

Refer to the exhibit. The USER that is connecting an application on an Internet connection in AS 100 is facing these issues:
- The USER lost the connection to the application during a failure between IG and R2.
- Router R2 configuration is lost due to a power outage.
- The application the USER is connecting to is hosted behind CE2.
What action resolves the issues on R3 and R4 routers?

A. Apply low Local Preference on R4 toward R2.

B. Apply high Local Preference on R3 toward R1.

C. Set R4 as a route reflector for R3 and CE2.

D. Set R3 as a route reflector for R4 and CE1.

Refer to the exhibit. An ISP engineer configured a VRF to isolate traffic for the customer ciscotest as shown. Now, the engineer must implement the Intra-AS VPN feature on PE1 to pass traffic between customer sites.
Which additional configuration must the engineer apply to PE1 to meet this requirement?

A. router bgp 64525 address-family ipv4 unicast neighbor 192.168.1.1 remote-as 64520 update-source Loopback0 address-family ipv4 unicast

B. router bgp 64525 address-family vpnv4 unicast neighbor 192.168.1.1 remote-as 64525 update-source Loopback0 address-family vpnv4 unicast

C. router bgp 64525 address-family ipv4 unicast neighbor 192.168.1.1 remote-as 64526 address-family ipv4 unicast

D. router bgp 64525 address-family vpnv4 unicast neighbor 192.168.1.1 remote-as 64516 update-source Loopback0 address-family vpnv4 unicast

Refer to the exhibit. A network engineer at ISP-B must advertise 198.19.100.0/24 `" 198.19.105.0/24 prefixes to ISP-A with these requirements:
- Prefixes 198.19.100.0/24 `" 198.19.102.0/24 must have the community set to 64602:10.
- Prefixes 198.19.103.0/24 `" 198.19.105.0/24 must have the community set to 64602:11.
The AS_PATH for the 198.19.103.0/24 `" 198.19.105.0/24 prefixes must appear as `64602 64602` in ASN 64601.

Which configuration must the engineer implement on the ISP-B router to meet the requirements?

A. configure terminal access-list 30 deny 198.19.100.0 0.0.0.255 access-list 30 deny 198.19.101.0 0.0.0.255 access-list 30 deny 198.19.102.0 0.0.0.255 ! route-map ASN-64601-OUT permit 10 match ip address 30 set as-path prepend 64602 64602 set community 64602:11 route-map ASN-64601-OUT permit 20 set community 64602:10 end

B. configure terminal access-list 30 deny 198.19.103.0 0.0.0.255 access-list 30 deny 198.19.104.0 0.0.0.255 access-list 30 deny 198.19.105.0 0.0.0.255 ! route-map ASN-64601-OUT deny 10 match ip address 30 set as-path prepend 64602 set community 64602:11 route-map ASN-64601-OUT permit 20 set community 64602:10 end

C. configure terminal access-list 30 deny 198.19.100.0 0.0.0.255 access-list 30 deny 198.19.101.0 0.0.0.255 access-list 30 deny 198.19.102.0 0.0.0.255 access-list 30 permit any ! route-map ASN-64601-OUT permit 10 match ip address 30 set as-path prepend 64602 set community 64602:11 route-map ASN-64601-OUT permit 20 set community 64602:10 end

D. configure terminal access-list 30 deny 198.19.100.0 0.0.0.255 access-list 30 deny 198.19.101.0 0.0.0.255 access-list 30 deny 198.19.102.0 0.0.0.255 access-list 30 permit any ! route-map ASN-64601-OUT permit 10 set community 64602:10 ! route-map ASN-64601-OUT permit 20 match ip address 30 set as-path prepend 64602 64602 set community 64602:11 end

A network architect plans to implement MPLS OAM to provide additional troubleshooting functionality for the NOC team. After analyzing the configuration on theMPLS P/PE nodes, the architect decides to revise the CoPP policies.
Which two actions ensure that the new solution is secure? (Choose two.)

A. Allow port 3505 in the outbound direction only.

B. Allow the ICMP protocol only.

C. Allow the TCP and UDP protocols.

D. Allow the UDP protocol only.

E. Allow port 3503 in the inbound direction only.

What is a feature of model-driven telemetry?

A. It occasionally streams to multiple servers in the network.

B. It is less secure because it uses community strings.

C. It uses the pull model to send requested data to a client when polled.

D. It uses the push model to stream data to desired destinations.

Refer to the exhibit. The link between Office A and Office B is running at 90% load, and occasionally the CPU on router R1 is overloaded. The company implemented QoS for business-critical applications at both offices as a temporary solution. A network engineer must update the R1 configuration to 600 ms to reduce CPU load and limit downtime after connection failure to avoid data loss.
Which action meets this requirement?

A. Configure the fast-hello feature for OSPF with the command ip ospf dead-interval minimal hello-multiplier 3.

B. Configure BFD demand mode with the command bfd-demand timer 150 interval 250 retransmit 5.

C. Configure BFD non-echo mode with the command echo interval 250 minimal 300 echo-multiplier 2.

D. Configure BFD echo mode with the command bfd interval 150 min_rx 200 multiplier 3.

Refer to the exhibit. A network engineer is configuring a new router for iBGP to improve the capacity of a growing network. The router must establish an iBGP peer relationship with its neighbor. The underlay network is already configured with the correct IP addresses.
Which step should the engineer apply to complete this task?

A. Implement multicast routing on the router to support BGP hellos.

B. Configure the AS number for the router to share with its iBGP peers.

C. Configure the new router as an iBGP route reflector to support multiple iBGP peers.

D. Activate the BGP peers under the correct address family on the router.

Refer to the exhibit. The application server in the data center hosts voice, video, and data applications over the internet. The data applications run more slowly than the voice and video applications. To ensure that all applications run smoothly, the service provider decided to implement a QoS policy on router PER 2 to apply traffic shaping.
Which two actions must an engineer take to implement the task? (Choose two.)

A. Configure the scheduling function to handle delayed packets.

B. Enable packet remarking for priority traffic.

C. Configure a queue to buffer excess traffic.

D. Set the token value for secondary traffic.

E. Set a threshold to discard excess traffic.

DRAG DROP -Drag and drop the characteristics from the left onto the corresponding radio splitting approaches on the right.
Select and Place: