Win IT Exam with Last Dumps 2025

DRAG DROP -A network engineer is adding an additional 10Gbps link to an existing 2x10Gbps LACP-based LAG to augment its capacity. Network standards require a bundle interface to be taken out of service if one of its member links goes down, and the new link must be added with minimal impact to the production network. Drag and drop the tasks that the engineer must perform from the left into the sequence on the right. Not all options are used.Select and Place:

Refer to the exhibit. Router 1 and router 2 are running IBGP, and router 2 and router 3 are running OSPF Area 0. Router 1 is advertising loopback interfaces Lo 0 and Lo 2, and router 2 is redistributing BGP into OSPF Area 0. Which configuration must an administrator apply so that router 2 uses a route map to redistribute only the internal route from Lo 2?

A. ip prefix-list BGP-to-ospf seq 5 permit 22.22.22.22/32 router bgp 100 bgp redistribute-internal route-map BGP-To-OSPF permit 10 match ip address prefix-list BGP-to-ospf router ospf 1 redistribute bgp 100 metric 100 metric-type 1 subnets route-map BGP-To-OSPF

B. ip prefix-list BGP-to-ospf seq 5 permit 22.22.22.0/24 router bgp 100 bgp redistribute-static route-map BGP-To-OSPF permit 10 match ip address prefix-list BGP-to-ospf router ospf 1 redistribute bgp 100 metric-type 2 route-map BGP-To-OSPF

C. ip prefix-list BGP-to-ospf seq 5 permit 22.22.22.0/24 router map BGP-To-OSPF permit 10 match ip address prefix-list BGP-to-ospf router ospf 1 redistribute bgp 100 metric 100 metric-type 1 subnet route-map BGP-To-OSPF

D. ip prefix-list BGP-to-ospf seq 5 permit 22.22.22.0/24 router map BGP-To-OSPF permit 10 match ip address prefix-list BGP-to-ospf router ospf 1 redistribute bgp 100 route-map BGP-To-OSPF

Refer to the exhibit. An engineer is configuring path selection on router R1 for two ASNs as shown. Which additional task must the engineer perform on Router 1 so that all outbound traffic utilizes the link between R1 and R3 to reach ASN 4567?

A. Configure a low weight on the peer to ASN 4567.

B. Configure a high weight on the peer to ASN 4567.

C. Configure an AS path prepend on the peer to ASN 4567.

D. Configure a high med on the peer to ASN 4567.

Refer to the exhibit. Router BRDR-1 is configured to receive the 0.0.0.0/0 and 172.17.1.0/24 networks via BGP and advertise them into OSPF area 0. An engineer has noticed that the OSPF domain is receiving only the 172.17.1.0/24 route and default route 0.0.0.0/0 is still missing. Which configuration must an engineer apply to resolve the problem?

A. router ospf 1 redistribute bgp 65001 metric 100 route-policy BGP-TO-OSPF end

B. router ospf 1 default-information originate end

C. router ospf 1 default-metric 100 end

D. router ospf 1 default-information originate always end

Refer to the exhibit. Router R1 is reporting that its BGP neighbor adjacency to router R2 is down, but its state is Active. Which configuration must be applied to routers R1 and R2 to fix the problem?

A. R1 router bgp 5400 neighbor 11.11.11.11 remote-as 5400 neighbor 11.11.11.11 update-source Loopback0 R2 router bgp 5400 neighbor 11.11.11.12 remote-as 5400 neighbor 11.11.11.12 update-source Loopback0

B. R1 router bgp 5400 neighbor 2.2.2.2 remote-as 5400 neighbor 2.2.2.2 update-source Loopback0 R2 router bgp 5400 neighbor 1.1.1.1 remote-as 5400 neighbor 1.1.1.1 update-source Loopback0

C. R1 router bgp 5400 neighbor 2.2.2.2 remote-as 5400 R2 router bgp 5400 neighbor 1.1.1.1 remote-as 5400

D. R1 router bgp 5400 neighbor 1.1.1.1 remote-as 5400 neighbor 1.1.1.1 update-source Loopback0 R2 router bgp 5400 neighbor 2.2.2.2 remote-as 5400 neighbor 2.2.2.2 update-source Loopback0

Refer to the exhibit. A network operator is attempting to configure an IS-IS adjacency between two routers, but the adjacency cannot be established. To troubleshoot the problem, the operator collects this debugging output.Which interfaces are misconfigured on these routers?

A. The R2 interface is configured as point-to-point, and the peer router interface is configured as multipoint.

B. The R2 interface is configured as Level 1 only, and the peer router interface is configured as Level 2 only. Most Voted

C. The peer router interface is configured as point-to-point, and the R2 interface is configured as multipoint.

D. The peer router interface is configured as Level 1 only, and the R2 interface is configured as Level 2 only.

Refer to the exhibit. An engineer has started to configure a router for OSPF, as shown. Which configuration must an engineer apply on the network so that area 15 traffic from R5 to R1 will prefer the route through R4?

A. Implement a sham link on the link between R3 and R2 to extend area 0 over area 15.

B. Implement a multiarea adjacency on the link between R2 and R4, with the cost manipulated to make the path through R4 preferred. Most Voted

C. Place the link between R3 and R5 in a stub area to force traffic to use the route through R4.

D. Increase the cost on the link between R2 and R3 to a value higher than the link between R2 and R4, to influence the path over R3 and R4.

An engineer working for a private service provider with employee Id: 1234:56:789 is configuring a Cisco device to redistribute OSPF into BGP. Which task enables the device to filter routes?

A. Configure an access list and reference it with the redistribute command.

B. Configure a route map and reference it with the redistribute command.

C. Configure a prefix list and associate it to the BGP peer interface.

D. Configure a distribute list and associate it to the BGP peer interface.

Refer to the exhibit. An engineer is configuring multitopology IS-IS for IPv6 on router R1. Which additional configuration must be applied to the router to complete the task?

A. R1# configure terminal R1(config)# router isis area2 R1(config-router)# address-family ipv6 R1(config-router-af)# multi-topology Most Voted

B. R1# configure terminal R1(config)# router isis area1 R1(config-router)# metric-style wide level-2 R1(config-router)# address-family ipv6 R1(config-router-af)# multi-topology

C. R1# configure terminal R1(config)# router isis area2 R1(config-router)# metric-style wide R1(config-router)# address-family ipv6 R1(config-router-af)# multi topology

D. R1# configure terminal R1(config)# router isis area1 R1(config-router)# metric-style wide level-1 R1(config-router)# address-family ipv6 R1(config-router-af)# multi topology

Refer to the exhibit. A network operator has two IPv4 and IPv6 dual-stacked networks on each side of the IPv4 core network. The operator must be able to provide connectivity between them while using specific assigned IPv6 space provided from the company IP administrator team. Which technology should the network operator use to accomplish this goal?

A. 6rd

B. DS-Lite

C. NAT44

D. NAT46