Question 481
Refer to the exhibit
Which command must be applied to R2 for an OSPF neighborship to form?
A. network 20.1.1.0 0.0.0.0 area 0
B. network 20.1.1.2 0.0.0.0 area 0
C. network 20.0.0.2 0.0.0.3 area 0
D. network 20.0.0.2 0.0.0.0 area 0
Question 482
What is one characteristic of VXLAN?
A. It supports a maximum of 4096 VLANs
B. It supports multitenant segments
C. It uses STP to prevent loops in the underlay network
D. It uses the Layer 2 header to transfer packets through the network underlay
Question 483
What is the function of vBond in a Cisco SD-WAN deployment?
A. initiating connections with SD-WAN routers automatically
B. pushing of configuration toward SD-WAN routers
C. onboarding of SD-WAN routers into the SD-WAN overlay
D. gathering telemetry data from SD-WAN routers
Question 484
Refer to the exhibit. A network administrator configured RSPAN to troubleshoot an issue between switch 1 and switch2. The switches are connected using interface GigabitEthernet 1/1. An external packet capture device is connected to swich2 interface GigabitEthernet 1/2
Which two commands must be added to complete this configuration? (Choose two.)
A. switch2(config-if)# switchport trunk allowed vlan 10,20,30,40,50,60,70-80
B. switch2(config)# monitor session 1 source remote vlan 70 switch2(config)# monitor session 1 destination interface GigabitEthernet1/2
C. switch1(config)# interface GigabitEthernet 1/1 switch1 (config-if)# switchport mode access switch1 (config-if)# switchport access vlan 10 switch2(config)# interface GigabitEthernet 1/1 switch2(config-if)# switchport mode access switch2(config-if)# switchport access vlan 10
D. switch2(config)# monitor session 2 destination vlan 10
E. switch2(config)# monitor session 1 source remote vlan 70 switch2(config)# monitor session 1 destination interface GigabitEthernet1/1
Question 485
Which function does a Cisco SD-Access extended node perform?
A. provides fabric extension to nonfabric devices through remote registration and configuration
B. performs tunneling between fabric and nonfabric devices to route traffic over unknown networks
C. used to extend the fabric connecting to downstream nonfabric enabled Layer 2 switches
D. in charge of establishing Layer 3 adjacencies with nonfabric unmanaged node
Question 486
Which router is elected the IGMP Querier when more than one router is in the same LAN segment?
A. The router with the shortest uptime.
B. The router with the longest uptime.
C. The router with the highest IP address.
D. The router with the lowest IP address.
Question 487
DRAG DROP -Drag and drop the characteristics from the left onto the switching mechanisms they describe on the right.
Select and Place:
Question 488
In which two ways does the routing protocol OSPF differ from EIGRP? (Choose two.)
A. OSPF provides shorter convergence time than EIGRP.
B. OSPF supports only equal-cost load balancing EIGRP supports unequal-cost load balancing.
C. OSPF is distance vector protocol. EIGRP is a link-state protocol.
D. OSPF supports an unlimited number of hops EIGRP supports a maximum of 255 hops.
E. OSPF supports unequal-cost load balancing EIGRP supports only equal-cost load balancing.
Question 489
Refer to the exhibit. A network engineer must configure the router to use the ISE-Servers group for authentication. If both ISE servers are unavailable, the local username database must be used. If no usernames are defined in the configuration, then the enable password must be the last resort to log in
Which configuration must be applied to achieve this result?
A. aaa authorization exec default group ISE-Servers local enable
B. aaa authentication login error-enable aaa authentication login default group enable local ISE-Servers
C. aaa authentication login default group ISE-Servers local enable
D. aaa authentication login default group enable local ISE-Servers
Question 490
When using BFD in a network design, which consideration must be made?
A. BFD is used with dynamic routing protocols to provide subsecond convergence.
B. BFD is used with first hop routing protocols to provide subsecond convergence.
C. BFD is used with NSF and graceful to provide subsecond convergence.
D. BFD is more CPU-intensive than using reduced hold timers with routing protocols.
