Win IT Exam with Last Dumps 2024

Refer to the exhibit. Which command when applied to the Atlanta router reduces type 3 LSA flooding into the backbone area and summarizes the inter-area routes on the Dallas router?

A. Atlanta(config-router)#area 0 range 192.168.0.0 255.255.252.0 B. Atlanta(config-router)#area 1 range 192.168.0.0 255.255.248.0 C. Atlanta(config-router)#area 0 range 192.168.0.0 255.255.248.0 D. Atlanta(config-router)#area 1 range 192.168.0.0 255.255.252.0

An engineer must configure interface GigabitEthernet0/0 for VRRP group 10. When the router has the highest priority in the group, it must assume the master role.Which command set must be added to the initial configuration to accomplish this task?Initial Configuration -interface GigabitEthernet0/0description To IDF A 38-24-044.40ip address 172.16.13.2 255.255.255.0

A. standby 10 ip 172.16.13.254 255.255.255.0 standby 10 preempt B. vrrp group 10 ip 172.16.13.254 255.255.255.0 vrrp group 10 priority C. standby 10 ip 172.16.13.254 standy 10 priority 120 D. vrrp 10 ip 172.16.13.254 vrrp 10 preempt

DRAG DROP -Drag and drop the characteristics from the left onto the routing protocols they describe on the right.Select and Place:

Refer to the exhibit. Which two commands ensure that DSW1 becomes the root bridge for VLAN 10 and 20? (Choose two.)

A. spanning-tree mst 1 priority 4096 B. spanning-tree mst 1 root primary C. spanning-tree mst vlan 10,20 priority root D. spanning-tree mst 1 priority 1 E. spanning-tree mstp vlan 10,20 root primary

Refer to the exhibit. R1 is able to ping the R3 fa0/1 interface. Why do the extended pings fail?

A. The maximum packet size accepted by the command is 1476 bytes. B. The DF bit has been set. C. R3 is missing a return route to 10.99.69.0/30. D. R2 and R3 do not have an OSPF adjacency.

Refer to the exhibit. Which command allows hosts that are connected to FastEthernet0/2 to access the Internet?

A. ip nat inside source list 10 interface FastEthernet0/2 overload B. ip nat inside source list 10 interface FastEthernet0/1 overload C. ip nat outside source static 209.165.200.225 10.10.10.0 overload D. ip nat outside source list 10 interface FastEthernet0/2 overload

Refer to the exhibit. What are two effects of this configuration? (Choose two.)

A. If R1 goes down, R2 becomes active but reverts to standby when R1 comes back online. B. If R2 goes down, R1 becomes active but reverts to standby when R2 comes back online. C. R1 becomes the active router. D. R1 becomes the standby router. E. If R1 goes down, R2 becomes active and remains the active device when R1 comes back online.

Refer to the exhibit. An engineer must ensure that all traffic entering AS 200 from AS 100 chooses Link 2 as an entry point. Assume that all BGP neighbor relationships have been formed and that the attributes have not been changed on any of the routers. Which configuration accomplishes this task?

A. R3(config)#route-map PREPEND permit 10 R3(config-route-map)#set as-path prepend 200 200 200 R3(config)#router bgp 200 R3#(config-router)#neighbor 10.1.1.1 route-map PREPEND out B. R4(config)#route-map PREPEND permit 10 R4(config-route-map)#set as-path prepend 100 100 100 R4(config)#router bgp 200 R4(config-router)#neighbor 10.2.2.2 route-map PREPEND in C. R4(config)#route-map PREPEND permit 10 R4(config-route-map)#set as-path prepend 200 200 200 R4(config)#router bgp 200 R4(config-router)#neighbor 10.2.2.2 route-map PREPEND out D. R3(config)#route-map PREPEND permit 10 R3(config-route-map)#set as-path prepend 100 100 100 R3(config)#router bgp 200 R3(config-router)#neighbor 10.1.1.1 route-map PREPEND in

Which DHCP option provides the CAPWAP APs with the address of the wireless controller(s)?

A. 43 B. 66 C. 69 D. 150

Refer to the exhibit.Which two commands ensure that DSW1 becomes root bridge for VLAN 10? (Choose two.)

A. DSW1(config)#spanning-tree vlan 10 priority 4096 Most Voted B. DSW1(config)#spanning-tree vlan 10 priority root C. DSW2(config)#spanning-tree vlan 10 priority 61440 Most Voted D. DSW1(config)#spanning-tree vlan 10 port-priority 0 E. DSW2(config)#spanning-tree vlan 20 priority 0