Win IT Exam with Last Dumps 2024

Refer to the exhibit. An engineer configured BGP between routers R1 and R3. The BGP peers cannot establish neighbor adjacency to be able to exchange routes. Which configuration resolves this issue?

A. R1 router bgp 6501 address-family ipv6 neighbor AB01:2011:7:100::3 activate

B. R3 router bgp 6502 address-family ipv6 neighbor AB01:2011:7:100::1 activate

C. R1 router bgp 6501 neighbor AB01:2011:7:100::3 ebgp-multihop 255

D. R3 router bgp 6502 neighbor AB01:2011:7:100::1 ebgp-multihop 255

Refer to the exhibit. Which action resolves the adjacency issue?

A. Configure the same autonomous system numbers.

B. Match the hello interval timers.

C. Match the authentication keys.

D. Configure the same EIGRP process IDs.

Refer to the exhibit. BGP and EIGRP are mutually redistributed on R3, and EIGRP and OSPF are mutually redistributed on R1. Users report packet loss and interruption of service to applications hosted on the 10.1.1.0/24 prefix. An engineer tested the link from R3 to R4 with no packet loss present but has noticed frequent routing changes on R3 when running the debug ip route command. Which action stabilizes the service?

A. Reduce frequent OSPF SPF calculations on R3 that cause a high CPU and packet loss on traffic traversing R3.

B. Tag the 10.1.1.0/24 prefix and deny the prefix from being redistributed into OSPF on R1.

C. Place an OSPF distribute-list outbound on R3 to block the 10.1.1.0/24 prefix from being advertised back to R3.

D. Repeat the test from R4 using ICMP ping on the local 10.1.1.0/24 prefix, and fix any Layer 2 errors on the host or switch side of the subnet

Refer to the exhibit. An engineer has configured policy-based routing and applied the configuration to the correct interface. How is the configuration applied to the traffic that matches the access list?

A. It is forwarded using the routing table lookup.

B. It is sent to 209.165.202.129.

C. It is dropped.

D. It is sent to 209.165.202.131.

Refer to the exhibit. A network administrator reviews the branch router console log to troubleshoot the OSPF adjacency issue with the DR router. Which action resolves this issue?

A. Stabilize the DR site flapping link to establish OSPF adjacency.

B. Advertise the branch WAN interface matching subnet for the DR site.

C. Configure the WAN interface for DR site in the related OSPF area.

D. Configure matching hello and dead intervals between sites.

Refer to the exhibit. When the FastEthernet0/1 goes down, the route to 172.29.0.0/16 via 192.168.253.2 is not installed in the RIB. Which action resolves the issue?

A. Configure feasible distance greater than the reported distance.

B. Configure feasible distance greater than the successor's feasible distance.

C. Configure reported distance greater than the successor's feasible distance.

D. Configure reported distance greater than the feasible distance.

Refer to the exhibit. AS111 is receiving its own routes from AS200 causing a loop in the network. Which configuration provides loop prevention?

A. router bgp 111 neighbor 195.1.1.1 as-override no neighbor 195.1.2.2 allowas-in

B. router bgp 111 no neighbor 195.1.1.1 allowas-in no neighbor 195.1.2.2 allowas-in

C. router bgp 111 neighbor 195.1.2.2 as-override no neighbor 195.1.1.1 allowas-in

D. router bgp 111 neighbor 195.1.1.1 as-override neighbor 195.1.2.2 as-override

Refer to the exhibit. AS65510 iBGP is configured for directly connected neighbors. R4 cannot ping or traceroute network 192.168.100.0/24. Which action resolves this issue?

A. Configure R1 as a route reflector server and configure R2 and R3 as route reflector clients.

B. Configure R4 as a route reflector server and configure R2 and R3 as route reflector clients.

C. Configure R4 as a route reflector server and configure R1 as a route reflector client.

D. Configure R1 as a route reflector server and configure R4 as a route reflector client.

Users report issues with reachability between areas as soon as an engineer configured summary routes between areas in a multiple area OSPF autonomous system. Which action resolves the issue?

A. Configure the area range command on the ASBR.

B. Configure the summary-address command on the ASBR.

C. Configure the summary-address command on the ABR.

D. Configure the area range command on the ABR.

Refer to the exhibit. Which set of commands restore reachability to loopback0?

A. interface loopback0 ip address 4.4.4.4 255.255.255.0 ip ospf network point-to-point

B. interface loopback0 ip address 4.4.4.4 255.255.255.0 ip ospf interface area 10

C. interface loopback0 ip address 4.4.4.4 255.255.255.0 ip ospf network broadcast

D. interface loopback0 ip address 4.4.4.4 255.255.255.0 ip ospf interface type network