Win IT Exam with Last Dumps 2024


Cisco 300-410 Exam

Page 21/30
Viewing Questions 201 210 out of 298 Questions
70.00%

Question 201
Refer to the exhibit. A network administrator is troubleshooting OSPF adjacency issue by going through the console logs in the router, but due to an overwhelming log messages stream, it is impossible to capture the problem.
Which two commands reduce console log messages to relevant OSPF neighbor problem details so that the issue can be resolved? (Choose two.)
Image 300-410_201Q.png related to the Cisco 300-410 Exam
A. debug condition ospf neighbor
B. debug condition interface
C. debug condition session-id ADJCHG
D. debug condition all

Question 202
Refer to the exhibit.
A network is under a cyberattack. A network engineer connected to R1 by SSH and enabled the terminal monitor via SSH session to find the source and destination of the attack. The session was flooded with messages, which made it impossible for the engineer to troubleshoot the issue.
Which command resolves this issue on R1?
Image 300-410_202Q.png related to the Cisco 300-410 Exam
A. (config)#terminal no monitor
B. (config)#no terminal monitor
C. #no terminal monitor
D. #terminal no monitor

Question 203
Refer to the exhibit.
A network administrator has developed a Python script on the local Linux machine and is trying to transfer it to the router. However, the transfer fails.
Which action resolves this issue?
Image 300-410_203Q.png related to the Cisco 300-410 Exam
A. The Python interpreter must first be enabled with the guestshell enable command.
B. The SSH access must be allowed on the VTY lines using the transport input ssh command.
C. The SSH service must be enabled with the crypto key generate rsa command.
D. The SCP service must be enabled with the ip scp server enable command.

Question 204
Refer to the exhibit.
An engineer configured SNMP communities on the Core_Sw1, but the SNMP server cannot obtain information from Core_Sw1.
Which configuration resolves this issue?
Image 300-410_204Q.png related to the Cisco 300-410 Exam
A. access-list 20 permit 10.221.10.11
B. snmp-server group NETADMIN v3 priv read NETVIEW write NETADMIN access 22
C. snmp-server group NETVIEW v2c priv read NETVIEW access 20
D. access-list 20 permit 10.221.10.12

Question 205
Refer to the exhibit.
Which two commands provide the administrator with the information needed to resolve the issue? (Choose two.)
Image 300-410_205Q.png related to the Cisco 300-410 Exam
A. debug snmpv3 engine-id
B. show snmp user
C. debug snmp packet
D. debug snmp engine-id
E. show snmpv3 user


Question 206
Refer to the exhibit.
The network administrator can see the DHCP discovery packet in R1, but R2 is not replying to the DHCP request. The R1 related interface is configured with theDHCP helper address. If the PC is directly connected to the Fa0/1 interface on R2, the DHCP server assigns as IP address from the DHCP pool to the PC.
Which two commands resolve this issue? (Choose two.)
Image 300-410_206Q.png related to the Cisco 300-410 Exam
A. service dhcp-relay command on R1
B. ip dhcp relay information enable command on R1
C. ip dhcp option 82 command on R2
D. service dhcp command on R1
E. ip dhcp relay information trust-all command on R2

Question 207
A network administrator performed a Compact Flash Memory upgrade on a Cisco Catalyst 6509 Switch. Everything is functioning normally except SNMP, which was configured to monitor the bandwidth of key interfaces but the interface indexes are changed.
Which global configuration resolves the issue?
A. snmp-server ifindex persist
B. snmp-server ifindex permanent
C. snmp ifindex persist
D. snmp ifindex permanent

Question 208
Refer to the exhibit. R1 is configured with IP SLA to check the availability of the server behind R6 but it kept failing.
Which configuration resolves the issue?
Image 300-410_208Q.png related to the Cisco 300-410 Exam
A. R6(config)#ip sla responder udp-echo ip address 10.10.10.1 port 5000
B. R6(config)#ip access-list extended DDOS R6(config-ext-nacl)#5 permit icmp host 10.10.10.1 host 10.66.66.66
C. R6(config)#ip sla responder
D. R6(config)#ip access-list extended DDOS R6(config-ext-nacl)#5 permit icmp host 10.66.66.66 host 10.10.10.1

Question 209
Refer to the exhibit. An engineer configured IP SLA on R1 to avoid the ISP link flapping problem, but it is not working as designed. IP SLA should wait 30 seconds before switching traffic to a secondary connection and then revert to the primary link after waiting 20 seconds, when the primary link is available and stabilized.
Which configuration resolves the issue?
Image 300-410_209Q.png related to the Cisco 300-410 Exam
A. R1(config)#track 700 ip sla 700 R1 (config-track)#delay down 30 up 20
B. R1 (config)#ip sla 700 R1(config-ip-sla)#delay down 30 up 20
C. R1 (config)#ip sla 700 R1(config-ip-sla)#delay down 20 up 30
D. R1(config)#track 700 ip sla 700 R1(config-track)#delay down 20 up 30

Question 210
Refer to the exhibit. An engineer must block access to the console ports for all corporate remote Cisco devices based on the recent corporate security policy but the security team still can connect through the console port.
Which configuration on the console port resolves the issue?
Image 300-410_210Q.png related to the Cisco 300-410 Exam
A. login and password
B. exec 0 0
C. transport input telnet
D. no exec