Refer to the exhibit. R2 is a route reflector, and R1 and R3 are route reflector clients. The route reflector learns the route to 172.16.25.0/24 from R1, but it does not advertise to R3. What is the reason the route is not advertised?
A. R2 does not have a route to the next hop, so R2 does not advertise the prefix to other clients.
B. Route reflector setup requires full IBGP mesh between the routers.
C. In route reflector setup, only classful prefixes are advertised to other clients.
D. In route reflector setups, prefixes are not advertised from one client to another.
Question 12
Refer to the exhibit. An engineer is trying to redistribute OSPF to BGP, but not all of the routes are redistributed. What is the reason for this issue?
A. By default, only internal routes and external type 1 routes are redistributed into BGP
B. Only classful networks are redistributed from OSPF to BGP
C. BGP convergence is slow, so the route will eventually be present in the BGP table
D. By default, only internal OSPF routes are redistributed into BGP
Question 13
Refer to the exhibit. In which circumstance does the BGP neighbor remain in the idle condition?
A. if prefixes are not received from the BGP peer
B. if prefixes reach the maximum limit
C. if a prefix list is applied on the inbound direction
D. if prefixes exceed the maximum limit
Question 14
Which attribute eliminates LFAs that belong to protected paths in situations where links in a network are connected through a common fiber?
A. shared risk link group-disjoint
B. linecard-disjoint
C. lowest-repair-path-metric
D. interface-disjoint
Question 15
Refer to the exhibit. An engineer is troubleshooting BGP on a device but discovers that the clock on the device does not correspond to the time stamp of the log entries. Which action ensures consistency between the two times?
A. Configure the service timestamps log uptime command in global configuration mode.
B. Configure the logging clock synchronize command in global configuration mode.
C. Configure the service timestamps log datetime localtime command in global configuration mode.
D. Make sure that the clock on the device is synchronized with an NTP server.
Question 16
Refer to the exhibit. What is the result of applying this configuration?
A. The router can form BGP neighborships with any other device.
B. The router cannot form BGP neighborships with any other device.
C. The router cannot form BGP neighborships with any device that is matched by the access list named "BGP".
D. The router can form BGP neighborships with any device that is matched by the access list named "BGP".
Question 17
Which command displays the IP routing table information that is associated with VRF-Lite?
A. show ip vrf
B. show ip route vrf
C. show run vrf
D. show ip protocols vrf
Question 18
Refer to the exhibit. Which subnet is redistributed from EIGRP to OSPF routing protocols?
A. 10.2.2.0/24
B. 10.1.4.0/26
C. 10.1.2.0/24
D. 10.2.3.0/26
Question 19
Which configuration adds an IPv4 interface to an OSPFv3 process in OSPFv3 address family configuration?
A. router ospfv3 1 address-family ipv4
B. Router(config-router)#ospfv3 1 ipv4 area 0
C. Router(config-if)#ospfv3 1 ipv4 area 0
D. router ospfv3 1 address-family ipv4 unicast
Question 20
Refer to the exhibit. Which statement about R1 is true?
A. OSPF redistributes RIP routes only if they have a tag of one.
B. RIP learned routes are distributed to OSPF with a tag value of one.
C. R1 adds one to the metric for RIP learned routes before redistributing to OSPF.
D. RIP routes are redistributed to OSPF without any changes.
