Win IT Exam with Last Dumps 2024

Refer to the exhibit. Web traffic is coming in from the WAN interface. Which route takes precedence when the router is processing traffic destined for the LAN network at 10.0.10.0/24?

A. via next-hop 10.0.1.5

B. via next-hop 10.0.1.4

C. via next-hop 10.0.1.50

D. via next-hop 10.0.1.100

OSPF must be configured between routers R1 and R2. Which OSPF configuration must be applied to router R1 to avoid a DR'BDR election?

A. router ospf 1 network 192.168.1.1 0.0.0.0 area 0 interface e1/1 ip address 192.168.1.1 255.255.255.252 ip ospf cost 0

B. router ospf 1 network 192.168.1.1 0.0.0.0 area 0 hello interval 15 interface e1/1 ip address 192.168.1.1 255.255.255.252

C. router ospf 1 network 192.168.1.1 0.0.0.0 area 0 interface e1/1 ip address 192.168.1.1 255.255.255.252 ip ospf network broadcast

D. router ospf 1 network 192.168.1.1 0.0.0.0 area 0 interface e1/1 ip address 192.168.1.1 255.255.255.252 ip ospf network point-to-point

Refer to the exhibit. An engineer is updating the R1 configuration to connect a new server to the management network. The PCs on the management network must be blocked from pinging the default gateway of the new server. Which command must be configured on R1 to complete the task?

A. R1(config)#ip route 172.16.2.0.255.255.255.0 192.168.1.15

B. R1(config)#ip route 172.16.2.2 255.255.255.248 gi0/1

C. R1(config)#ip route 172.16.2.2 255.255.255.255 gi0/0

D. R1(config)#ip route 172.16.2.0 255.255.255.0 192.168.1.5

Refer to the exhibit. Router R1 currently is configured to use R3 as the primary route to the internet, and the route uses the default administrative distance settings. A network engineer must configure R1 so that it uses R2 as a backup, but only if R3 goes down. Which command must the engineer configure on R1 so that it correctly uses R2 as a backup route, without changing the administrative distance configuration on the link to R3?

A. ip route 0.0.0.0 0.0.0.0 209.165.201.5.10

B. ip route 0.0.0.0 0.0.0.0 g0/1 1

C. ip route 0.0.0.0 0.0.0.0 209.165.200.226 1

D. ip route 0.0.0.0 0.0.0.0 g0/1 6

An engineer is configuring router R1 with an IPv6 static route for prefix 2019:C15C:0CAF:E001::/64. The next hop must be 2019:C15C:0CAF:E002::1. The route must be reachable via the R1 Gigabit 0/0 interface. Which command configures the designated route?

A. F0/10

B. F0/11

C. F0/12

D. F0/1

Refer to the exhibit. If OSPF is running on this network, how does Router2 handle traffic from Site B to 10.10.13.128/25 at Site A?

A. It sends packets out of interface Fa0/1.

B. It sends packets out of interface Fa0/2.

C. It load-balances traffic out of Fa0/1 and Fa0/2.

D. It is unreachable and discards the traffic.

Refer to the exhibit. Router R1 resides in OSPF Area 0. After updating the R1 configuration to influence the paths that it will use to direct traffic, an engineer verified that each of the four Gigabit interfaces has the same route to 10 10.0.0/16.
Which interface will R1 choose to send traffic to reach the route?

A. GigabitEthernet0/0

B. GigabitEthernet0/1

C. GigabitEthernet0/2

D. GigabitEthernet0/3

Refer to the exhibit. Which network prefix was learned via EIGRP?

A. 172.160.0/16

B. 207.165.200.0/24

C. 192.168.1.0/24

D. 192.168.2.0/24

Refer to the exhibit. Which command must be issued to enable a floating static default route on router A?

A. ip route 0.0.0.0 0.0.0.0 192.168.1.2 10

B. ip route 0.0.0.0 0.0.0.0 192.168.1.2

C. ip default-gateway 192.168.2.1

D. ip route 0.0.0.0 0.0.0.0 192.168.2.1 10

Refer to the exhibit. Which configuration allows routers R14 and R86 to form an OSPFv2 adjacency while acting as a central point for exchanging OSPF information between routers?

A. R14# interface FastEthernet0/0 ip address 10.73.65.65 255.255.255.252 ip ospf network broadcast ip ospf priority 0 ip mtu 1400 router ospf 10 router-id 10.10.1.14 network 10.10.1.14 0.0.0.0 area0 network 10.73.65.64 0.0.0.3 area0 R86# interface Loopback0 ip address 10.10.1.86 255.255.255.255 interface FastEthernet0/0 ip address 10.73.65.66 255.255.255.252 ip ospf network broadcast ip mtu 1500 router ospf 10 router-id 10.10.1.86 network 10.10.1.86 0.0.0.0 area 0 network 10.73.65.64 0.0.0.3 area 0

B. R14# interface Loopback0 ip ospf 10 area 0 interface FastEthernet0/0 ip address 10.73.65.65 255.255.255.252 ip ospf network broadcast ip ospf 10 area 0 ip mtu 1500 router ospf 10 ip ospf priority 255 router-id 10.10.1 14 R86# interface Loopback0 ip ospf 10 area 0 interface FastEthernet0/0 ip address 10.73.65.66 255.255.255.252 ip ospf network broadcast ip ospf 10 area 0 ip mtu 1500 router ospf 10 router-id 10.10.1.86

C. R14# interface FastEthernet0/0 ip address 10.73.65.65 255.255.255.252 ip ospf network broadcast ip ospf priority 255 ip mtu 1500 router ospf 10 router-id 10.10.1.14 network 10.10.1.14 0.0.0.0 area0 network 10.73.65.64 0.0.0.3 area0 R86# interface FastEthernet0/0 ip address 10.73.65.66 255.255.255.252 ip ospf network broadcast ip mtu 1500 router ospf 10 router-id 10.10.1.86 network 10.10.1.86 0.0.0.0 area 0 network 10.73.65.64 0.0.0.3 area 0

D. R14# interface FastEthernet0/0 ip address 10.73.65.65 255.255.255.252 ip ospf network broadcast ip ospf priority 255 ip mtu 1500 router ospf 10 router-id 10.10.1.14 network 10.10.1.14 0.0.0.0 area0 network 10.73.65.64 0.0.0.3 area0 R86# interface FastEthernet0/0 ip address 10.73.65.66 255.255.255.252 ip ospf network broadcast ip mtu 1400 router ospf 10 router-id 10.10.1.86 network 10.10.1.86 0.0.0.0 area 0 network 10.73.65.64 0.0.0.3 area 0