Question 371
How does HSRP provide first hop redundancy?
A. It load-balances Layer 2 traffic along the path by flooding traffic out all interfaces configured with the same VLAN.
B. It uses a shared virtual MAC and a virtual IP address to a group of routers that serve as the default gateway for hosts on a LAN.
C. It forwards multiple packets to the same destination over different routed links in the data path.
D. It load-balances traffic by assigning the same metric value to more than one route to the same destination in the IP routing table.
Question 372
Refer to the exhibit. Which action establishes the OSPF neighbor relationship without forming an adjacency?
A. modify hello interval
B. modify process ID
C. modify priority
D. modify network type
Question 373
Which command must you enter to guarantee that an HSRP router with higher priority becomes the HSRP primary router after it is reloaded?
A. standby 10 preempt
B. standby 10 version 1
C. standby 10 priority 150
D. standby 10 version 2
Question 374
Which command should you enter to verify the priority of a router in an HSRP group?
A. show hsrp
B. show sessions
C. show interfaces
D. show standby
Question 375
Refer to the exhibit. Which command would you use to configure a static route on Router1 to network 192.168.202.0/24 with a nondefault administrative distance?
A. router1(config)#ip route 192.168.202.0 255.255.255.0 192.168.201.2 1
B. router1(config)#ip route 192.168.202.0 255.255.255.0 192.168.201.2 5
C. router1(config)#ip route 1 192.168.201.1 255.255.255.0 192.168.201.2
D. router1(config)#ip route 5 192.168.202.0 255.255.255.0 192.168.201.2
Question 376
Which of the following dynamic routing protocols are Distance Vector routing protocols?
A. IS-IS
B. EIGRP
C. OSPF
D. BGP
E. RIP
Question 377
You have configured a router with an OSPF router ID, but its IP address still reflects the physical interface. Which action can you take to correct the problem in the least disruptive way?
A. Reload the OSPF process
B. Specify a loopback address
C. Reboot the router
D. Save the router configuration
Question 378
Which command should you enter to view the error log in an EIGRP for IPv6 environment?
A. show ipv6 eigrp neighbors
B. show ipv6 eigrp topology
C. show ipv6 eigrp traffic
D. show ipv6 eigrp events
Question 379
Refer to the exhibit. Which two statements about the network environment of router R1 must be true? (Choose two.) Refer to the exhibit. Router R1 must be configured to reach the 10.0.3.0/24 network from the 10.0.1.0/24 segment. Which command must be used to configure the route?
A. route add 10.0.3.0 0.255.255.255 10.0.4.2
B. ip route 10.0.3.0 0.255.255.255 10.0.4.2
C. route add 10.0.3.0 mask 255.255.255.0 10.0.4.3
D. ip route 10.0.3.0 255.255.255.0 10.0.4.3
Question 380
Refer to the exhibit. Which two statements about the network environment of router R1 must be true? (Choose two.)
A. The EIGRP administrative distance was manually changed from 90 to 170.
B. There are 20 different network masks within the 10.0.0.0/8 network.
C. Ten routes are equally load-balanced between Te0/1/0.100 and Te0/2/0.100.
D. The 10.0.0.0/8 network was learned via external EIGRP.
E. A static default route to 10.85.33.14 was defined.
