Win IT Exam with Last Dumps 2024

What must a network administrator consider when deciding whether to configure a new wireless network with APs in autonomous mode or APs running in cloud- based mode?

A. Autonomous mode APs are less dependent on an underlay but more complex to maintain than APs in cloud-based mode. B. Cloud-based mode APs relay on underlays and are more complex to maintain than APs in autonomous mode. C. Cloud-based mode APs are easy to deploy but harder to automate than APs in autonomous mode. D. Autonomous mode APs are easy to deploy and automate than APs in cloud-based mode.

When a switch receives a frame for an unknown destination MAC address, how is the frame handled?

A. flooded to all ports except the origination port B. forwarded to the first available port C. broadcast to all ports on the switch D. inspected and dropped by the switch

Which state is bypassed in Rapid PVST+ when PortFast is enabled on a port?

A. blocking B. forwarding C. learning D. discarding

What happens when a switch receives a frame with a destination MAC address that recently aged out?

A. The switch floods the frame to all ports in all VLANs except the port that received the frame. B. The switch floods the frame to all ports in the VLAN except the port that received the frame. C. The switch references the MAC address aging table for historical addresses on the port that received the frame. D. The switch drops the frame and learns the destination MAC address again from the port that received the frame.

What is a function of store-and forward switching?

A. It reduces latency by eliminating error checking within the frame B. It produces an effective level of error-free network traffic using CRCs. C. It buffers frames and forwards regardless of errors within the frames. D. It forwards a frame by checking only the destination MAC address

Refer to the exhibit. Switch AccSw1 has just been added to the network along with PC2. All VLANs have been implemented on AccSw2. How must the ports on AccSw2 be configured to establish Layer 2 connectivity between PC1 and PC2?

A. interface GigabitEthernet1/2 switchport mode access switchport access vlan 2 ! interface GigabitEthernet1/24 switchport mode trunk B. interface GigabitEthernet1/1 switchport mode access switchport access vlan 11 ! interface GigabitEthernet1/24 switchport mode trunk C. interface GigabitEthernet1/24 switchport mode trunk switchport trunk allowed vlan 11, 12 ! interface GigabitEthernet1/1 switchport access vlan 11 D. interface GigabitEthernet1/2 switchport mode access switchport access vlan 12 ! interface GigabitEthernet1/24 switchport mode trunk switchport trunk allowed vlan 11, 12

Refer to the exhibit. A network engineer must update the configuration on Switch2 so that it sends LLDP packets every minute and the information sent via LLDP is refreshed every 3 minutes. Which configuration must the engineer apply?

A. Switch2(config)#lldp timer 60 Switch2(config)#lldp tlv-select 180 B. Switch2(config)#lldp timer 60 Switch2(config)#lldp holdtime 180 C. Switch2(config)#lldp timer 1 Switch2(config)#lldp holdtime 3 D. Switch2(config)#lldp timer 1 Switch2(config)#lldp tlv-select 3

Refer to the exhibit. Switch A is newly configured. All VLANs are present in the VLAN database. The IP phone and PC A on Gi0/1 must be configured for the appropriate VLANs to establish connectivity between the PCs. Which command set fulfills the requirement?

A. SwitchA(config-if)#switchport mode access SwitchA(config-if)#switchport access vlan 50 SwitchA(config-if)#switchport voice vlan 51 B. SwitchA(config-if)#switchport mode trunk SwitchA(config-if)#switchport trunk allowed vlan add 50, 51 SwitchA(config-if)#switchport voice vlan dot1p C. SwitchA(config-if)#switchport mode trunk SwitchA(config-if)#switchport trunk allowed vlan 50, 51 SwitchA(config-if)#mis qos trust cos D. SwitchA(config-if)#switchport mode access SwitchA(config-if)#switchport access vlan 50 SwitchA(config-if)#switchport voice vlan untagged

Refer to the exhibit. Two new switches are being installed. The remote monitoring team uses the support network to monitor both switches. Which configuration is the next step to establish a Layer 2 connection between the two PCs?

A. SwitchA(config)#interface GigabitEthernet0/1 SwitchA(config-if)#switchport access vlan 500 SwitchB(config)#interface GigabitEthernet0/1 SwitchB(config-if)#switchport access vlan 500 B. SwitchA(config)#interface GigabitEthernet0/1 SwitchA(config-if)#switchport mode trunk SwitchB(config)#interface GigabitEthernet0/1 SwitchB(config-if)#switchport mode trunk C. SwitchA(config)#interface GigabitEthernet0/0 SwitchA(config-if)#switchport trunk allowed vlan 500, 550 SwitchB(config)#interface GigabitEthernet0/0 SwitchB(config-if)#switchport trunk allowed vlan 500, 550 D. SwitchA(config)#interface GigabitEthernet0/0 SwitchA(config-if)#spanning-tree portfast SwitchA(config-if)#spanning-tree bpduguard enable SwitchB(config)#interface GigabitEthernet0/0 SwitchB(config-if)#spanning-tree portfast SwitchB(config-if)#spanning-tree bpduguard enable

Refer to the exhibit. An engineer is configuring a new Cisco switch, NewSW, to replace SW2. The details have been provided: - Switches SW1 and SW2 are third-party devices without support for trunk ports, - The existing connections must be maintained between PC1, PC2, and PC3, - Allow the switch to pass traffic from future VLAN 10. Which configuration must be applied?

A. NewSW(config)#interface f0/0 NewSW(config-if)#switchport mode trunk NewSW(config-if)#switchport trunk native vlan 10 NewSW(config-if)#switchport trunk native vlan 10 B. NewSW(config)#interface f0/0 NewSW(config-if)#switchport mode access NewSW(config-if)#switchport trunk allowed vlan 2, 10 NewSW(config-if)#switchport trunk native vlan 2 C. NewSW(config)#interface f0/0 NewSW(config-if)#switchport mode access NewSW(config-if)#switchport trunk allowed vlan 2, 10 NewSW(config-if)#switchport trunk native vlan 10 D. NewSW(config)#interface f0/0 NewSW(config-if)#switchport mode trunk NewSW(config-if)#switchport trunk allowed vlan 2, 10 NewSW(config-if)#switchport trunk native vlan 2