Question 211
Refer to the exhibit. A network engineer is trying to retrieve SNMP MIBs with RESTCONF on the Cisco switch but fails. End-to-end routing is in place.
Which configuration must the engineer implement on the switch to complete the task?
A. snmp-server community public RO
B. snmp-server community cisco RW
C. netconf-yang cisco-ia snmp-community-string Public
D. netconf-yang cisco-ia snmp-community-string Private
Question 212
Refer to the exhibit. Users in AS 65010 are connected with the application server in AS 65050 with these requirements:
AS 65010 users are experiencing latency and congestion to connect with application server 172.16.50.10.
- AS 65030 must be restricted to become Transient Autonomous System for traffic flow.
- Links connected to AS 65020 and AS 65040 are underutilized and must be used efficiently for traffic.
Which two configurations must be implemented to meet these requirements? (Choose two.)
A. Apply the AS-Path route-map policy for traffic received from R3.
B. Configure the route map to prepend the AS-Path attribute for R5-R3 BGP peering.
C. Apply the MED route-map policy for traffic received from R4.
D. Configure a higher Local preference for R5-R4 BGP peering.
E. Configure the route map to set the MED 50 attribute for R5-R4 BGP peering.
Question 213
What is a characteristic of MVPN?
A. It bypasses the use of MPLS in the service provider core and transmits packets using IP only.
B. It uses pseudowires to route unicast and broadcast traffic over either a service provider MPLS or IP core.
C. It allows VRF traffic to use the service provider MPLS VPN to route multicast traffic.
D. It creates GRE tunnels to route multicast traffic over a service provider IP core.
Question 214
Refer to the exhibit. What is the purpose of this JSON script?
A. It changes the existing password.
B. It updates a user authentication record.
C. It deletes a user's authentication record.
D. It confirms a user's login credentials.
Question 215
A network engineer must implement SNMPv2 with these parameters:
- Enable SNMP community string c1sc0 with read-only permissions.
- Enable interface index persistence.
Restrict the SNMP community to only the monitoring server with IP address 198.18.19.100/32.
- Provide view-only access to ospfIfEntry and ospfNbrEntry.
Which configuration must the engineer apply?
A. configure terminal access-list 5 permit 198.18.19.100 0.0.0.0 snmp-server view BLOCKED_VIEW internet excluded snmp-server view BLOCKED_VIEW ospfIfEntry included snmp-server view BLOCKED_VIEW ospfNbrEntry included snmp-server community c1sc0 view BLOCKED_VIEW RO snmp ifmib ifindex persist end
B. configure terminal access-list 5 permit 198.18.19.100 0.0.0.0 snmp-server view BLOCKED_VIEW internet excluded snmp-server view BLOCKED_VIEW ospfIfEntry included snmp-server view BLOCKED_VIEW ospfNbrEntry included snmp-server community c1sc0 view BLOCKED_VIEW RO 5 snmp ifmib ifindex persist end
C. configure terminal access-list 5 permit 198.18.19.100 0.0.0.0 snmp-server view BLOCKED_VIEW internet included snmp-server view BLOCKED_VIEW ospfIfEntry included snmp-server view BLOCKED_VIEW ospfNbrEntry included snmp-server community c1sc0 view BLOCKED_VIEW RO snmp ifmib ifindex persist end
D. configure terminal access-list 5 permit 198.18.19.100 0.0.0.0 snmp-server view BLOCKED_VIEW internet excluded snmp-server view BLOCKED_VIEW ospfIfEntry included snmp-server view BLOCKED_VIEW ospfNbrEntry included snmp-server community c1sc0 view BLOCKED_VIEW RW 5 snmp ifmib ifindex persist end
Question 216
The network team is planning to implement IPv6 on the company's existing IPv4 network infrastructure. The network currently uses IS-IS to share routes between peers.
Which task must the team perform so that IS-IS will run in multitopology mode on the updated IPv6 network?
A. Configure the links between the network routers as point-to-point.
B. Configure the network routers to use metric-style wide.
C. Configure the network routers as Level 2 routers.
D. Configure the IS-IS IPv6 metric on the dual-stack links.
Question 217
Refer to the exhibit. ISP A provides VPLS services and DDoS protection to Company XYZ to connect their branches across the North America and Europe regions. The uplink from the data center to the ISP is 100 Mbps. The Company XYZ security team asked the ISP to redirect ICMP echo requests, which are currently going to the web server, to a new local security appliance.
Which configuration must an ISP engineer apply to router R2 to redirect the ICMP traffic?
A. class-map type traffic match-all B_210.10.65.1 match destination-address ipv4 210.10.65.1 match protocol 7 match ipv4 icmp-type 3
B. class-map type traffic match-all B_210.10.65.1 match destination-address ipv4 210.10.65.1 match protocol 1 match ipv4 icmp-type 8
C. class-map type traffic match-all B_210.10.65.1 match destination-address ipv4 210.10.65.1 match protocol 3 match ipv4 icmp-type 5
D. class-map type traffic match-all B_210.10.65.1 match destination-address ipv4 210.10.65.1 match protocol 6 match ipv4 icmp-type 9
Question 218
A customer has requested that the service provider use a Cisco MPLS TE tunnel to force the E-Line service to take a specific route. What is used to send the traffic over the tunnel?
A. forwarding adjacency
B. autoroute destination
C. preferred path
D. static route
Question 219
When Cisco IOS XE REST API uses HTTP request methods, what is the purpose of a PUT request?
A. updates the specified resource with new information
B. creates a new resource
C. submits data to be processed to the specified resource
D. retrieves the specified resource or representation
Question 220
A network engineer must configure a router for Flexible NetFlow IPFIX export. The IP address of the destination server is 172.17.12.1. The source address must be set to the Loopback0 IPv4 address and exported packets must be set to DSCP CS3. The TTL must be 64 and the transport protocol must be set to UDP with destination port 4739.
Which configuration must the engineer apply to the router?
A. configure terminal flow exporter EXPORTER-1 destination 172.17.12.1 source Loopback0 dscp 3 ttl 64 export-protocol netflow-v9 transport udp 4739 end
B. configure terminal flow exporter EXPORTER-1 destination 172.17.12.1 source Loopback0 dscp 24 ttl 64 export-protocol ipfix end
C. configure terminal flow exporter EXPORTER-1 destination 172.17.12.1 source Loopback0 dscp 24 ttl 64 export-protocol netflow-v9 transport udp 4739 end
D. configure terminal flow exporter EXPORTER-1 destination 172.17.12.1 source Loopback0 dscp 3 ttl 64 export-protocol ipfix end
