Refer to the exhibit. An engineer must create a configuration that prevents R3 from receiving the LSA about 172.16.1.4/32. Which configuration set achieves this goal?
A. On R3 ip access-list standard R4_L0 deny host 172.16.1.4 permit any router ospf 200 distribute-list R4_L0 in
B. On R1 ip prefix-list INTO-AREA1 seq 5 deny 172.16.1.4/32 ip prefix-list INTO-AREA1 seq 10 permit 0.0.0.0/0 le 32 router ospf 200 area 1 filter-list prefix INTO-AREA1 out
C. On R1 ip prefix-list INTO-AREA1 seq 5 deny 172.16.1.4/32 ip prefix-list INTO-AREA1 seq 10 permit 0.0.0.0/0 le 32 router ospf 200 area 1 filter-list prefix INTO-AREA1 in
D. On R3 ip prefix-list INTO-AREA1 seq 5 deny 172.16.1.4/32 ip prefix-list INTO-AREA1 seq 10 permit 0.0.0.0/0 le 32 router ospf 200 area 1 filter-list prefix INTO-AREA1 in
Question 382
Refer to the exhibit. An engineer is reaching network 172.16.10.0/24 via the R1-R2-R4 path. Which configuration forces the traffic to take a path of R1-R3-R4?
A. R1(config)#route-map RM_LOCAL_PREF permit 10 R1(config-route-map)#set local-preference 101 R1(config-route-map)#exit R1(config)#router bgp 100 R1(config-router)#neighbor 13.13.13.3 route-map RM_LOCAL_PREF in R1(config-router)#end R1#clear ip bgp 13.13.13.3 soft in
B. R1(config)#route-map RM_AS_PATH_PREPEND R1(config-route-map)#set as-path prepend 200 200 R1(config-route-map)#exit R1(config)#router bgp 100 R1(config-router)#neighbor 12.12.12.2 route-map RM_AS_PATH_PREPEND in R1(config-router)#end R1#clear ip bgp 12.12.12.2 soft in
C. R1(config)#router bgp 100 R1(config-router)#neighbor 13.13.13.3 weight 1 R1(config-router)#end
D. R2(config)#route-map RM_MED permit 10 R2(config-route-map)#set metric 1 R2(config-route-map)#exit R2(config)#router bgp 200 R2(config-router)#neighbor 12.12.12.1 route-map RM_MED out R2(config-router)#end R2#clear ip bgp 12.12.12.1 soft out
Question 383
In a Cisco SD-Access solution, which protocol is used by an extended node to connect to a single edge node?
A. VXLAN
B. IS-IS
C. 802.1Q
D. CTS
Question 384
Refer to the exhibit. How does the router handle traffic after the CoPP policy is configured on the router?
A. Traffic generated by R1 that matches access list SNMP is policed.
B. Traffic coming to R1 that matches access list SNMP is policed.
C. Traffic passing through R1 that matches access list SNMP is policed.
D. Traffic coming to R1 that does not match access list SNMP is dropped.
Question 385
What is a characteristic of Cisco StackWise technology?
A. It is supported on the Cisco 4500 series.
B. It supports devices that are geographically separated
C. It combines exactly two devices.
D. It uses proprietary cabling.
Question 386
What is one primary REST security design principle?
A. fail-safe defaults
B. password hash
C. adding a timestamp in requests
D. OAuth
Question 387
Refer to the exhibit. After the code is run on a Cisco IOS-XE router, the response code is 204. What is the result of the script?
A. The configuration fails because interface GigabitEthernet2 is missing on the target device.
B. Interface GigabitEthemet2 is configured with IP address 10.10.10.1/24.
C. The configuration fails because another interface is already configured with IP address 10.10.10.1/24.
D. The configuration is successfully sent to the device in cleartext.
Question 388
Which time protocol offers security features and utilizes site-local IPv6 multicast addresses?
A. NTPv3
B. PTP IEEE 1588v1
C. NTPv4
D. PTP IEEE 1588v2
Question 389
Refer to the exhibit Which command must be applied to Router1 to bring the GRE tunnel to an up/up state?
A. Router1(config-if)#tunnel source Loopback0
B. Router1(config-if)#tunnel mode gre multipoint
C. Router1(config-if)#tunnel source GigabitEthernet0/1
D. Router1(config)#interface tunnel0
Question 390
DRAG DROP -Drag and drop the characteristics from the left onto the infrastructure deployment models on the right. Select and Place:
